Науковий вісник НГУ

Information technologies in modeling operation modes of mining dewatering plant based on economic and mathematical analysis

• 
• 

User Rating:  / 1

PoorBest 

Details

Category: Contens №4 2020

Last Updated on 05 September 2020

Published on 30 August 2020

Hits: 3049

Authors:

Yu. A. Papaika, orcid.org/0000-0001-6953-1705, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

O. G. Lysenko, orcid.org/0000-0002-7041-671X, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

K. S. Rodna, orcid.org/0000-0002-3610-7091, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

O. S. Shevtsova, orcid.org/0000-0002-6421-8127, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2020, (4): 082-087

https://doi.org/10.33271/nvngu/2020-4/082

повний текст / full article

Abstract:

Purpose. To ensure the energy efficiency of coal mine power systems. This can be achieved by using rational modes of a sump plant under multifactor initial conditions.

Methodology. The research technique is based on the theory of economic and mathematical analysis and the general theory of electrical engineering.

Findings. For the first time we suggested using the criterion for maximizing the mathematical expectation of the integral (total) profit (savings) P_S(Y ). The foregoing allows us to select an economically feasible diameter for the discharge pipelines of mine drainage plants. The value of the economically feasible diameter (when using this criterion) is greater than when using the criterion of minimizing the production function P (Y ). Therefore, it is possible to achieve maximum economic efficiency. Using reserve pipelines allows the value of the production function P (Y ) to be decreased and the value of the integral (total) profit P_S(Y ) to be increased. For the first time, it has been noted that when using various criteria to determine the economically advantageous diameters of the main pipelines of a mine drainage plant, the value of the economically advantageous diameter does not depend on the number of reserve pipelines used.

Originality. The research presents the theoretical substantiation of the feasibility of using economic and mathematical analysis in the search for optimal operating modes of drainage plants. We established the dependencies between the parameters of the drainage unit and the indicators of economic efficiency. This allows us to optimize the electromechanical system for energy consumption. We proposed a method for selecting the number and diameter of pressure pipelines of a mine drainage plant, taking into account a set of technological parameters that provide maximum profit.

Practical value. We selected and justified the search criteria for the optimal mode of the electromechanical mine drainage. We also developed an algorithm and software package for determining the rational diameter and number of pipelines. Mathematical dependencies make it possible to optimize the operation of a drainage plant according to two criteria, which, taking into account 20 % of the electrical consumption by a drainage system in the mine’s energy balance, creates additional opportunities for increasing the energy efficiency of mining enterprises.

References.

1. Papaika, Yu., Pivnyak, G., & Zhezhelenko, I. (2018). Energy efficiency of power-supply systems: monograph. Dnipro: Dnipro University of Technology.

2. Pivnyak, G., Dychkovskyi, R., & Vagonova, O. (2017). Sustainable Development of Industrial Regions: monograph. In: Advanced Engineering Forum. Zurich, Switzerland.

3. Pivnyak, G., & Dychkovskyi, R. (2017). Energy Saving and Efficiency: Technological, Economical and Social Challenges: monograph. In: Advanced Engineering Forum. Zurich, Switzerland.

4. Papaika, Yu., Pivnyak, G., & Zhezhelenko, I. (2016). Estimating economic equivalent of reactive power in the systems of enterprise power supply. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (5), 62-66.

5. Shcherbak, Ya. V., Plakhtii, O. A., & Nerubatskiy, V. P. (2017). Regulatory characteristics of the active quadrature converter in regimens and recuperation modes. Technical electrodynamics, (6), 26-31. https://doi.org/10.15407/techned2017.06.026.

6. Volkov, V. A. (2017). Energy-saving control in start-brake regimes with the speed of a frequency regulated asynchronous engine with a fan load. Hirnycha electromekhanika ta avtomatyka, 99, 110-127.

7. Beshta, O. S., Fedoreiko, V. S., Palchyk, A. O., & Burega, N. V. (2015). Autonomous power supply of the objects based on biosolid oxide fuel systems. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (2), 67-73.

8. Ghavrish, A., & Shevtsova, O. (2015). The hydraulic impact and alleviation phenomena numeric modelling in the industrial pumped pipelines. In: Power Engineering, Control and Information Technologies in Geotechnical Systems, (pp. 143-153). London: Taylor & Francis Group. ISBN 978-1-138-02804-3.

9. Pivnyak, G., Dychkovskyi, R., Edgar Cáceres Cabana, & Smoliński, A. (2018). Non-Traditional Technologies in the Mining Industry. Solid State Phenomena. Monograph. Zurich: Trans Tech Publication Ltd.

10. Pivnyak, G., Dychkovskyi, R., Edgar Cáceres Cabana, Bobyliov, O., & Smoliński, A. (2018). Mathematical and Geomechanical Model in Physical and Chemical Processes of Underground Coal Gasification. Non-Traditional Technologies in the Mining Industry. In: Solid State Phenomena, (pp. 1-16). Zurich: Trans Tech Publication Ltd.

11. Beshta, O. S. (2012). Electric drives adjustment for improvement of energy efficiency of technological processes. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (4), 98-107.

12. Kosobudzki, G., & Florek, A. (2017). EMC Requirements for Power Drive Systems, Power Electronics and Drives, 2(2), 127-135. https://doi.org/10.5277/PED170207.

13. Lenoch, V., Masek, Z., Cermak, D., & Schejbal, V. (2018). Electromagnetic Compatibility of Pulse Rectifier with Pulse-width Modulation. 28 ^th International Conference Radioelektronika. https://doi.org/10.1109/RADIOELEK.2018.8376352.

14. Golovchenko, A. (2020). Some aspects of the control for the radial distribution of burden material and gas flow in the blast furnace. Energies, 13(4), 923-926, https://doi.org/10.3390/en13040923.

15. Golovchenko, A., Pazynich, Y., & Potempa, M. (2018). Automated monitoring of physical processes of formation of burden material surface and gas flow in blast furnace. Solid State Phenomena, 277, 54-65. https://doi.org/10.4028/www.scientific.net/SSP.277.54.

• < Prev
• Next >