Determination of the deformation parameters of the steel reinforcing phase inside the aluminum matrix during hot rolling
/ 0
- Details
- Parent Category: 2022
- Category: Content №6 2022
- Created on 25 December 2022
- Last Updated on 26 December 2022
- Published on 26 December 2022
- Written by M. Nosko, D. Konovodov, A. Samsonenko, O. Bobukh
- Hits: 2969
Authors:
M.Nosko, orcid.org/0000-0002-8792-4016, Ukrainian State University of Science and Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
D.Konovodov*, orcid.org/0000-0001-8282-4991, Ukrainian State University of Science and Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
A.Samsonenko, orcid.org/0000-0001-6992-2327, Ukrainian State University of Science and Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
O.Bobukh, orcid.org/0000-0001-7254-3854, Ukrainian State University of Science and Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
* Corresponding author e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2022, (6): 084 - 089
https://doi.org/10.33271/nvngu/2022-6/084
Abstract:
Purpose. Comparison of deformation parameters during rolling of reinforced composites based on aluminum alloy using braided and expanded steel meshes as a reinforcing phase.
Methodology. An experimental study on the effect of pressure on the deformation of the reinforcing phase during rolling of aluminum composites is carried out. A wire mesh and expanded mesh made of stainless steel was used as a reinforcing phase. The effect of deformation on the change in the lattice angle of the reinforcing phase is investigated.
Findings. In this work, experimental data on the parameters of deformation of the wire mesh and expanded mesh are obtained. A comparison is made of the shape change in such grids under hot rolling conditions between two aluminum plates, which play the role of a matrix. It is found that the elongation coefficients of the lattice for the experiment with a wire mesh c is equal to 1.682.3, which is greater than the coefficient of elongation of the lattice in the expanded mesh of 1.552.2. Therefore, expanded sheets make the best reinforcing layer for aluminum-based composites produced by the roll-bonding process. Expanded mesh also reduces the risk of rupture at the intersection of wires.
Originality. In the work, for the first time, a comparison of the deformation parameters during roll bonding of composites based on an aluminum alloy, reinforced with a braided and expanded steel mesh, has been given. Obtaining composite materials by means of hot roll bonding requires an understanding of the flow of composite components during deformation and their influence on each other. These peculiarities have not been studied sufficiently. Currently, there is no reliable method for predicting the behavior of the material of a solid reinforcing phase of various shapes inside a composite.
Practical value. Advantages of using an expanded steel mesh for reinforcing aluminum-based composites have been confirmed. Scientific results can be used to refine calculating methods for metal flow at high hydrostatic pressure with variable components of the stress tensor and the major stresses.
Keywords: roll bonding, aluminum matrix, steel mesh inlay, flat rolling, composite, deformation parameters
References.
1. Groche, P., Wohletz, S., Brenneis, M., Pabst, C., & Resch, F. (2014). Joining by forming a review on joint mechanisms, applications and future trends. Journal of Materials Processing Technology, 214(10), 1972-1994. https://doi.org/10.1016/j.jmatprotec.2013.12.022.
2. Spittel, M., & Spittel, T. (2011). Part 2: Non-ferrous Alloys Light Metals Al 99.5Al 99.5. In Metal Forming Data Non-Ferrous Alloys Light Metals deformation behaviour. Martienssen, W., & Warlimont,H., (Eds.), (pp 197-203). Springer Berlin Heidelberg: Berlin, Heidelberg. ISBN 978-3-642-13863-8.
3. Khan,H.A., Asim,K., Akram,F., Hameed,A., Khan,A., & Mansoor,B. (2021). Roll bonding processes: State-of-the-art and future perspectives. Metals, 11(9), 1344. https://doi.org/10.3390/met11091344.
4. Frolov,Y., Nosko,M., Samsonenko,A., Bobukh,O., & Remez,O. (2021). Roll bonding of al-based composite reinforced with C10 steel expanded mesh inlay. Metals, 11(7), 1044. https://doi.org/10.3390/met11071044.
5. Stolbchenko,M., Makeieva,H., Grydin,O., Frolov,Y., & Schaper,M. (2018). Roll Bonding of Steel Net-Reinforced Aluminium Strips. Materials Research, 21(2), 1-11. https://doi.org/10.1590/1980-5373-MR-2017-0941.
6. Stolbchenko, M., Makeieva, H., Grydin, O., Frolov, Y., & Schaper,M. (2018). Strain parameters at hot rolling of aluminum strips reinforced with steel netting. Journal of Sandwich Structures and Materials, 22(6), 2009-2029. https://doi.org/10.1177/1099636218792539.
7. Huang, H., Wang, J., & Liu, W. (2017). Mechanical properties and reinforced mechanism of the stainless steel wire meshreinforced Al-matrix composite plate fabricated by twin-roll casting. Advances in Mechanical Engineering, 9/6. 168781401771663. https://doi.org/10.1177/1687814017716639.
8. Frolov, Y., Stolbchenko, M., Grydin, O., Makeeva, H., Tershakovec, M., & Schaper, M. (2019). Influence of strain parameters at rolling on the properties of wire-reinforced aluminium composites. International Journal of Material Forming, 12(4), 505-518. https://doi.org/10.1007/s12289-018-1431-6.
9. Ferro,P., Fabrizi,A., Bonollo,F., & Berto,F. (2021). Microstructural and mechanical characterization of a stainless-steel wire meshreinforced al-matrix composite: Bimatallic components for lightweight design. Frattura Ed Integrit Strutturale, 15(55), 289-301. https://doi.org/10.3221/IGF-ESIS.55.22.
10. Chen, G., Li, J.T., Yu, H.L., Su, L.H., Xu, G.M., Pan, J.S., , & He, L.Z. (2016). Investigation on bonding strength of steel/aluminum clad sheet processed by horizontal twin-roll casting, annealing and cold rolling. Materials & Design, 112, 263-274. https://doi.org/10.1016/j.matdes.2016.09.061.
11. Glen, B., Kaya, Y., Durgutlu, A., Glen, I., Yildirim, M., & Kahraman, N. (2016). Production of wire reinforced composite materials through explosive welding. Archives of Civil and Mechanical Engineering, 16/1, 1-8. https://doi.org/10.1016/j.acme.2015.09.006.
12. Hufenbach, W., Ullrich, H., Gude, M., Czulak, A., Malczyk, P., & Geske, V. (2012). Manufacture studies and impact behaviour of light metal matrix composites reinforced by steel wires. Archives of Civil and Mechanical Engineering. 12/3, 265-272. https://doi.org/10.1016/j.acme.2012.06.005.
13. Jamaati, R., & Toroghinejad, M. (2010). Investigation of the parameters of the cold roll bonding (CRB) process. Materials Science and Engineering: , 527/9, 2320-2326. https://doi.org/10.1016/j.msea.2009.11.069.
14. Abbasi, M., & Toroghinejad, M. (2010). Effects of processing parameters on the bond strength of Cu/Cu roll-bonded strips. Journal of Materials Processing Technology, 210(3), 560-563. https://doi.org/10.1016/j.jmatprotec.2009.11.003.
15. Haranich, Y.Y., & Frolov, Y.V. (2016). Comprehensive analysis of metal polymer sandwich composite manufacturing. Treatment of Materials by Pressure, 2/45, 136-141.
16. Akramifard, H., Mirzadeh, H., & Parsa, M. (2014). Cladding of aluminum on AISI304L stainless steel by cold roll bonding: Mechanism, Microstructure, and Mechanical Properties. Materials Science and Engineering: , 613, 232-239. https://doi.org/10.1016/j.msea.2014.06.109.
17. Soltani, M., Jamaati, R., & Toroghinejad, M. (2012). The influence of TiO2 nano-particles on bond strength of cold roll bonded aluminum strips. Materials Science and Engineering: , 550, 367-374. https://doi.org/10.1016/j.msea.2012.04.089.
18. Grydin, O., Stolbchenko, M., & Schaper, M. (2016). Twin-roll casting of carbon fiber-reinforced and glass fiber-reinforced aluminum strips. InLight Metals 2016,(pp. 1007-1012). Springer, Cham. https://doi.org/10.1007/978-3-319-48251-4_168.
19. ASTM A240 Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications (n.d.). Retrieved from https://webstore.ansi.org/Standards/ASTM/astma240a240m10b.
Newer news items:
- Legal management and regulation of the activities of professional participants in the stock market of Ukraine - 25/12/2022 02:37
- The impact of the economic and COVID-19 crises on the Visegrad Group countries - 25/12/2022 02:37
- Digital technologies and their impact on economic and social spheres in Ukraine - 25/12/2022 02:37
- Improving transport logistics of extractive industry products in the context of capacity constraints on the railways - 25/12/2022 02:37
- Computer modeling of territory flooding in the event of an emergency at Seredniodniprovska Hydroelectric Power Plant - 25/12/2022 02:37
- Study on accumulation of heavy metals by green plantations in the conditions of industrial cities - 25/12/2022 02:37
- Heavy metals removal using natural zeolite adsorption from Tigris river water at Samarra city (Iraq) - 25/12/2022 02:37
- Improvement of the safe work system - 25/12/2022 02:37
- Impact of digital maturity on sustainable development effects in energy sector in the condition of Industry 4.0 - 25/12/2022 02:37
- Influence of misalignment of connection of electrical machine shafts on the nature of electric power of the induction motor - 25/12/2022 02:37
Older news items:
- Minimization of dynamic changes in the tension of long products behind the outlet cage in rolling stock production in coils - 25/12/2022 02:37
- Approximation of blades of radial machines with multiparameter family of smooth surfaces - 25/12/2022 02:37
- The influence of fissured material on tunnel stability (a numerical study) - 25/12/2022 02:37
- Taxonomy on the production processes and characterization of powder metallurgy used in additive manufacturing process - 25/12/2022 02:37
- Numerical study on deformation around underground mining structures (Algeria) - 25/12/2022 02:37
- Substantiation of research results on energy efficiency of basalt crushing - 25/12/2022 02:37
- Research on the rational profile of exit trails of auto transport in deep open mines - 25/12/2022 02:37
- Determining the parameters of stratification cavity in rock mass to extract mine methane - 25/12/2022 02:37
- Haul road condition impact on tire life of mining dump truck - 25/12/2022 02:37
- Mathematical modeling the quarry wall stability under conditions of heavily jointed rocks - 25/12/2022 02:37
