Articles

Transformation of the kirigami-type deformable inlay during roll bonding

• 
• 

User Rating:  / 0

PoorBest 

Details

Category: Content №1 2025

Last Updated on 25 February 2025

Published on 30 November -0001

Hits: 56

Authors:

Y.Frolov, orcid.org/0000-0001-6910-6223, Ukrainian State University of Science and Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

D.Konovodov*, orcid.org/0000-0001-8282-4991, Ukrainian State University of Science and Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

O.Bobukh, orcid.org/0000-0001-7254-3854, Ukrainian State University of Science and Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

V.Boiarkin, orcid.org/0009-0005-7582-9504, Ukrainian State University of Science and Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

^* Corresponding author e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

повний текст / full article

Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2025, (1): 034 - 039

https://doi.org/10.33271/nvngu/2025-1/034

Abstract:

Purpose. To quantitatively analyze the deformation of kirigami-type deformable inlays during the roll bonding process using soft outer matrices, with the goal of predicting their behavior within the composite structure.

Methodology. The research involved the fabrication of three-layer composite sheets through roll bonding. Expanded meshes made of mild steel and stainless steel served as the inlay phase, while copper and aluminum alloy sheets were employed as matrix materials. The transformation of the inlay phase within the composite sheets was evaluated.

Findings. The experimental investigation yielded data on the deformation behavior of kirigami-type inlays embedded within three-layer sheets during roll bonding. It was observed that using an aluminum matrix induces greater axial metal flow in the deformation zone, leading to a significant increase in the mesh distortion angle. A copper matrix primarily causes flattening of the mesh cells with minimal changes to their angular deformation. In contrast, rolling the steel mesh without a matrix results in negligible angular distortion until the rolling reduction exceeds 50 %.

Originality. This study represents the first quantitative analysis of the geometric transformation of kirigami-type deformable inlays as a function of deformation magnitude and matrix material properties during roll bonding. Understanding the shape transformation of the reinforcing phase within the composite sheet enables more accurate prediction of the contact area between the matrix materials during the bonding process.

Practical value. The findings of this research provide a basis for predicting the final geometry of kirigami structures within composite materials.

Keywords: roll bonding, expanded steel mesh, aluminum matrix, copper matrix

References.

1. Frolov, Y., Haranich, Y., Bobukh, O., Remez, O., Voswinkel, D., & Grydin, O. (2020). Deformation of expanded steel mesh inlay inside aluminum matrix during the roll bonding. Journal of Manufacturing Processes, 58, 857-867. https://doi.org/10.1016/j.jmapro.2020.08.049.

2. Tao, J., Khosravi, H., Deshpande, V., & Li, S. (2022). Engineering by Cuts: How Kirigami Principle Enables Unique Mechanical Properties and Functionalities. Advanced Science, 2204733. https://doi.org/10.1002/advs.202204733.

3. Jin, L., Forte, A. E., Deng, B., Rafsanjani, A., & Bertoldi, K. (2020). Kirigami-Inspired Inflatables with Programmable Shapes. Advanced Materials, 32(33), 2001863. https://doi.org/10.1002/adma.202001863.

4. Hwang, D.-G., & Bartlett, M. D. (2018). Tunable Mechanical Metamaterials through Hybrid Kirigami Structures. Scientific Reports, 8(1). https://doi.org/10.1038/s41598-018-21479-7.

5. Neville, R. M., Scarpa, F., & Pirrera, A. (2016). Shape morphing Kirigami mechanical metamaterials. Scientific Reports, 6(1). https://doi.org/10.1038/srep31067.

6. Zhang, Y., Li, P., Quan, J., Li, L., Zhang, G., & Zhou, D. (2022). Progress, Challenges, and Prospects of Soft Robotics for Space Applications. Advanced Intelligent Systems, 2200071. https://doi.org/10.1002/aisy.202200071.

7. Song, W., Yoo, S., Song, G., Lee, S., Kong, M., Rim, J., Jeong, U., & Park, S. (2019). Recent Progress in Stretchable Batteries for Wearable Electronics. Batteries & Supercaps, 2(3), 181-199. https://doi.org/10.1002/batt.201800140.

8. Wang, W., Rodrigue, H., Kim, H.-I., Han, M.-W., & Ahn, S.-H. (2016). Soft composite hinge actuator and application to compliant robotic gripper. Composites Part B: Engineering on Science Direct, 98, 397-405. https://doi.org/10.1016/j.compositesb.2016.05.030.

9. Yang, Y., Vallecchi, A., Shamonina, E., Stevens, C. J., & You, Z. (2023). A new class of transformable kirigami metamaterials for reconfigurable electromagnetic systems. Scientific Reports, 13(1). https://doi.org/10.1038/s41598-022-27291-8.

10. Blees, M. K., Barnard, A. W., Rose, P. A., Roberts, S. P., McGill, K. L., Huang, P. Y., …, & McEuen, P. L. (2015). Graphene kirigami. Nature, 524(7564), 204-207. https://doi.org/10.1038/nature14588.

11. Hashimoto, M., & Taguchi, Y. (2020). Design and Fabrication of a Kirigami-Inspired Electrothermal MEMS Scanner with Large Displacement. Micromachines, 11(4), 362. https://doi.org/10.3390/mi11040362.

12. Han, D. X., Zhao, L., Chen, S. H., Wang, G., & Chan, K. C. (2021). Critical transitions in the shape morphing of kirigami metallic glass. Journal of Materials Science & Technology, 61, 204-212. https://doi.org/10.1016/j.jmst.2020.05.065.

13. Gong, X., Yang, Q., Zhi, C., & Lee, P. S. (2020). Stretchable Energy Storage Devices: From Materials and Structural Design to Device Assembly. Advanced Energy Materials, 2003308. https://doi.org/10.1002/aenm.202003308.

14. Babaee, S., Pajovic, S., Rafsanjani, A., Shi, Y., Bertoldi, K., & Traverso, G. (2020). Bioinspired kirigami metasurfaces as assistive shoe grips. Nature Biomedical Engineering, 4(8), 778-786. https://doi.org/10.1038/s41551-020-0564-3.

15. Kim, K. K., Suh, Y., & Ko, S. H. (2020). Smart Stretchable Electronics for Advanced Human–Machine Interface. Advanced Intelligent Systems, 2000157. https://doi.org/10.1002/aisy.202000157.

16. Lamoureux, A., Lee, K., Shlian, M., Forrest, S. R., & Shtein, M. (2015). Dynamic kirigami structures for integrated solar tracking. Nature Communications, 6(1). https://doi.org/10.1038/ncomms9092.

17. Sareh, S., & Rossiter, J. (2012). Kirigami artificial muscles with complex biologically inspired morphologies. Smart Materials and Structures, 22(1), 014004. https://doi.org/10.1088/0964-1726/22/1/014004.

18. Chen, Y., Liang, Q., Ji, C.-Y., Liu, X., Wang, R., & Li, J. (2022). A magnetic actuation scheme for nano-kirigami metasurfaces with reconfigurable circular dichroism. Journal of Applied Physics, 131(23), 233102. https://doi.org/10.1063/5.0091180.

19. Jang, N.-S., Kim, K.-H., Ha, S.-H., Jung, S.-H., Lee, H. M., & Kim, J.-M. (2017). Simple Approach to High-Performance Stretchable Heaters Based on Kirigami Patterning of Conductive Paper for Wearable Thermotherapy Applications. ACS Applied Materials & Interfaces, 9(23), 19612-19621. https://doi.org/10.1021/acsami.7b03474.

20. Frolov, Y., Bobukh, O., Samsonenko, A., & Nurnberger, F. (2023). Patterning of Surfaces for Subsequent Roll Bonding in a Low-Oxygen Environment Using Deformable Mesh Inlays. Journal of Manufacturing Processes, 7(5), 158. https://doi.org/10.3390/jmmp7050158.

21. Nosko, M., Konovodov, D., Samsonenko, A., & Bobukh, O. (2022). Determination of the dedormation parameters of the steel reinforcing phase inside the aluminum matrix during hot rolling. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (6), 84-89. https://doi.org/10.33271/nvngu/2022-6/084.

22. Frolov, Y., Nosko, M., Samsonenko, A., Bobukh, O., & Remez, O. (2021). Roll Bonding of Al-Based Conposite Reinforced with C10 Steel Expanded Mesh Inlay. Metals, 11(7), 1044. https://doi.org/10.3390/met11071044.

23. Chen, S. H., Chan, K. C., Han, D. X., Zhao, L., & Wu, F. F. (2019). Programmable super elastic kirigami metallic glasses. Materials and Design, 169, 107687. https://doi.org/10.1016/j.matdes.2019.107687.

24. Isobe, M., & Okumura, K. (2016) Initial rigid response and softening transition of highly stretchable kirigami sheet materials. Scientific Reports, 6. https://doi.org/10.1038/srep24758.

25. Frolov, Y., Stolbchenko, M., Grydin, O., Makeeva, H., Tersha­ko­vec, M., & Schaper, M. (2019). Influence of strain parameters at rolling on the properties of wire-reinforced aluminium composites. International Journal of Material Forming, 12(4), 505-518. https://doi.org/10.1007/s12289-018-1431-6.

26. QForm UK. Windows; Micas Simulations Limited: Oxford, UK, 2023. Retrieved from https://qform3d.com.

• < Prev
• Next >