Sodium silicate solute foaming in a flat slot-type capillary under microwave radiation influence
/ 0
- Details
- Category: Content №6 2020
- Last Updated on 22 December 2020
- Published on 30 November -0001
- Hits: 2715
Authors:
L.I.Solonenko, orcid.org/0000-0003-2092-8044, Odesa National Polytechnic University, Odesa, Ukraine, -mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
R.V.Usenko, orcid.org/0000-0002-8007-9702, National Metallurgical Academy of Ukraine, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
A.V.Dziubina, orcid.org/0000-0002-2215-7231, National Metallurgical Academy of Ukraine, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
K.I.Uzlov, orcid.org/0000-0003-0744-9890, National Metallurgical Academy of Ukraine, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
S.I.Repiakh, orcid.org/0000-0003-0203-4135, National Metallurgical Academy of Ukraine, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2020, (6): 034 - 040
https://doi.org/10.33271/nvngu/2020-6/034
Abstract:
Purpose. A mass transferring mechanism during liquid glass foaming in flat slot-type capillary under microwave radiation influence has been determined.
Methodology. Sodium soda silicate solute with silicate module of 2.83.0 and specific gravity of 1.431.46 g/cm3 is used in the studies. For sodium silicate solute coloring, red ink is added. Treatment of sodium silicate solute water solution with microwave radiation is carried out in a furnace with a working chamber volume of 23 liters, with nominal magnetron power of 700 W and radiation frequency of 2450 MHz. Investigation of the structure of foamed sodium silicate solute is done by the optical microscopy method with magnifications of 25 to 200 times. Microwave furnace internal temperature is measured using non-contact electronic infrared thermometer Temperature AR 320. Mass determination is carried out on electronic balance with 0.01 g accuracy. Liquid glass foaming is organized in a flat slot-type capillary with thickness of 30 to 900 m formed by two glass plates parallel to each other.
Findings. A mechanism of sodium silicate solute mass transferring during its foaming in a flat slot-type capillary when heated by microwave radiation description is developed. It is established that sodium silicate solute transferring in a capillary proceeds in stages according to a scheme similar to a chain reaction. The scheme includes: sodium silicate solute self-encapsulation due to appearance of shell on free surface of partially dehydrated sodium silicate solute; vapor bubble in capsule formation; increasing steam pressure in capsule; capsule shell destruction and ejection of part of unhardened sodium silicate solute out of the capsule; complete removal of sodium silicate solute from the capsule and its destruction under high vapor pressure influence; movement finalization of stream of sodium silicate solute ejected outside the capsule, its repeated self-encapsulation, and so on. This process repeats until water removal from the treated sodium silicate solute will be completed. Sodium silicate solute foam structure formation staging and certain cyclical nature under microwave radiation effects is the main cause of substantial no uniformity of pore dispersion and resulting foam permeability.
Originality. For the first time, description of a mechanism of mass transferring of sodium silicate solute foamed in a flat slot-type capillary when heated by microwave radiation has been developed. For the first time it has been determined that sodium silicate solute with silica modulus of 2.8 to 3.0 microwave radiation processing allows reducing water content in dried sodium silicate solute to value less than 0.1% (wt.).
Practical value. Sodium silicate solute foaming by microwave radiation is a perspective process from the point of view of developing new methods and approaches for solving the problem of optimization of granular material structuring and, in particular, for manufacturing molds and cores. Understanding of sodium silicate solute foaming mechanism will allow increasing the accuracy of predicting the structure of foams produced on sodium silicate solute basis and properties, optimizing the process parameters for their pores formation, expanding the knowledge concerning technological possibilities of implementing sodium silicate solute in porous environments structuring, dehydration by microwave radiation, and so on.
Keywords: mass transferring, vapor, sodium silicate solute, water, capillary, capsule, foaming, microwave radiation
References.
1. Abdrakhimov, V.Z., Abdrakhimov, E.S., & Abdrakhimov,I.D. (2017). Getting insulating material based in liquid glass and coal conversion wastes generated during coking coal preparation. Ugol Russian Coal Journal, 4, 64-67. https:// doi.org/10.18796/0041-5790-2017-4-64-67.
2. Siqian Zhang, Yu-Ri Lee, Whan Ahn, & Wha-Seung Ahn (2018). Sodium silicate insulating foam reinforced with acid-treated fly ash. Materials Letters, 218(1), 56-59. https://doi.org/10.1016/j.matlet.2018.01.150.
3. Abdrakhimov, E.S. (2019). Use of waste fuel and energy complex burned rocks and tailings of chromite ore in the production of porous aggregate on the basis of liquid-glass compositions. Ugol Russian Coal Journal, 7, 67-69. https://doi.org/10.18796/0041-5790-2019-7-67-69.
4. Kogan, V.E. (2016). Inorganic and organic vitreous foam materials and prospect of environmental cleaning from oil and oil products pollutions. Journal of Miming Institute, 218, 331-337. ISSN 0135-3500.
5. Romero, A.R., Toniolo, N., Boccaccini, A.R., & Bernardo,E. (2019). Glass-Ceramic Foams from Weak Alkali Activation and Gel-Casting of Waste Glass. Fly Ash Mixtures. Materials, 12(588), 1-14. https://doi.org/10.3390/ma12040588.
6. Wattanasiriwech, D., Nontachit, S., Manomaivibool, P., & Wattanasiriwech, S. (2019). Foam glass from municipal waste as a lightweight aggregate for cement mortar. IOP Conferens Series: Earth and Environmental Science, 351, 1-6. https://doi.org/10.1088/1755-1315/351/1/012008.
7. Paunescu, L., Dragoescu, M.F., Axinte, S.M., & Sebez,A.C. (2019). Nonconventional technique for producing high mechanical strength glass foam from glass waste. Journal of Engineering Studies and Research, 2, 48-55. https://doi.org/10.29081/jesr.v25i2.320.
8. Garca-Moreno, F. (2016). Commercial Applications of Metal Foams: Their Properties and Production. Materials, 9(85), 2-27. https://doi.org/10.3390/ma9020085.
9. Ye Li, Xudong Cheng, Wei Cao, Lunlun Gong, Ruifang Zhang, & Heping Zhang (2016). Development of adiabatic foam using sodium silicate modified by boric acid. Journal of Alloys and Compounds, 666, 513-519. https://doi.org/10.1016/j.jallcom.2016.01.139.
10. Gilyazidinova, N., Rudkovskaya, N., & Santalova, T. (2018). Nature conservation technology for producing slag-foam glass as a structural and thermal insulating material. E3S Web of Conferences, IIIrd International Innovative Mining Symposium, 41, 1-7. https://doi.org/10.1051/e3sconf/20184102017.
11. Zhigulina, A., & Mizuriaev, S. (2017).Technology of obtaining thermal insulation material on the basis of liquid glass by a method of low temperature processing. MATEC Web of Conferences, Theoretical Foundation of Civil Engineering, 117, 1-7. https://doi.org/10.1051/matecconf/20171170018.
12. Tkachenko, S.S., Kolodiy, G.A., Znamensky, L.G., & Ermolenko, A.A. (2018). Cold mixture of inorganic binder: status and prospects of development (inorganic vs. organic). Foundry production and metallurgy, 2(91), 16-22. https://doi.org/10.21122/1683-6065-2018-2-16-22.
13. Solonenko, L., Prokopovich, I., Repyakh, S., Sukhoi, K., & Dmytrenko, D. (2019). System analysis of modern areas of increasing environmental and sanitary hygienic safety of using cold hardening mixtures in foundry. Odessa Polytechnic University, Proceedings, 1(57), 90-98. ISSN2076-2429.
14. Solonenko, L.I., Bilyi, O.P., Repiakh, S.I., Kimstach,T.V., & Uzlov, K.I. (2020). Heating rate of granular inorganic materials by microwave radiation. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (2), 37-41. https://doi.org/10.33271/nvngu/2020-2/037.
Newer news items:
- Determining conditions of using draglines in single-tier internal dump formation - 22/12/2020 00:15
- Obtaining kinetic characteristics of combustion of the coke from solid biofuels - 22/12/2020 00:15
- Influence of particle geometry on the efficiency of operation of quasistatic and inertial disintegrators - 22/12/2020 00:15
- Dynamic analysis of thin laminated viscoelastic structures under elevated temperature using finite element modeling - 22/12/2020 00:15
- Effect of alloying heat-resistant packing coatings on their tribotechnical, physical and mechanical properties - 22/12/2020 00:15
- Forecasting of wear of pads of modernized brake system devices of bogies of freight cars using ARIMA models - 22/12/2020 00:15
- Assessment of geotechnical properties of Draa El Mizane highway tunnel (Algeria) - 22/12/2020 00:15
- Energy-efficient predictive control for field-orientation induction machine drives - 22/12/2020 00:15
- Integrated system of modular power supply and multilevel control of brushless dc motor for electric vehicles - 22/12/2020 00:15
- Adaptation of the high-pressure electrolyzer in the conditions of joint operation with TPP and NPP power-generating units - 22/12/2020 00:15
Older news items:
- Determining conditions of using draglines in single-tier internal dump formation - 22/12/2020 00:15
- Obtaining kinetic characteristics of combustion of the coke from solid biofuels - 22/12/2020 00:15
- Influence of particle geometry on the efficiency of operation of quasistatic and inertial disintegrators - 22/12/2020 00:15
- Dynamic analysis of thin laminated viscoelastic structures under elevated temperature using finite element modeling - 22/12/2020 00:15
- Effect of alloying heat-resistant packing coatings on their tribotechnical, physical and mechanical properties - 22/12/2020 00:15
- Forecasting of wear of pads of modernized brake system devices of bogies of freight cars using ARIMA models - 22/12/2020 00:15
- Assessment of geotechnical properties of Draa El Mizane highway tunnel (Algeria) - 22/12/2020 00:15
- Energy-efficient predictive control for field-orientation induction machine drives - 22/12/2020 00:15
- Integrated system of modular power supply and multilevel control of brushless dc motor for electric vehicles - 22/12/2020 00:15
- Adaptation of the high-pressure electrolyzer in the conditions of joint operation with TPP and NPP power-generating units - 22/12/2020 00:15
Archive