Articles

Force and pressure function formulation for direct cold extrusion of aluminum alloy Al 1350 using regression method

• 
• 

User Rating:  / 4

PoorBest 

Details

Category: Content №3 2021

Last Updated on 23 June 2021

Published on 30 November -0001

Hits: 4921

Authors:

Fadi Alfaqs, orcid.org/0000-0003-3427-6454, Faculty of Engineering Technology, Department of Mechanical Engineering, Al-Balqa Applied University, Jordan, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

Ghazi S.Marahleh, orcid.org/0000-0003-4750-9245, Faculty of Engineering Technology, Department of Mechanical Engineering, Al-Balqa Applied University, Jordan, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

повний текст / full article

Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2021, (3): 038 - 043

https://doi.org/10.33271/nvngu/2021-3/038

Abstract:

Purpose. Establishing methodology in order to determine mathematically both extrusion force and pressure functions for Aluminum alloy AL 1350 using the regression method of experimental data.

Methodology. Several variables (diameter of the cavity for pressing D, degree of extrusion, angle of the punch head cone 2, and ratio of the semi-finished sizes R_s) were included when using the regression method considered.

Findings. Diameter and strain were found to play a significant role in predicting both extrusion force and pressure functions associated with the extrusion process. Mathematical formulas for force and pressure were obtained using the regression method. Amethodology has been developed for the mathematical determination of extrusion force and pressure.

Originality. Force and pressure functions in direct cold extrusion process are mainly required for the design of extrusion dies. However, the existence of such data in the literature is insufficient to implement the process for direct cold extrusion of aluminum and aluminum alloys as well as for other materials. Results of the study consider the main factors influencing extrusion force and pressure as well as the main differences for types of aluminum alloys.

Practical value. The mathematical formulas obtained by the regression method provide a mathematical tool for calculating force and pressure values in direct extrusion process.

Keywords: aluminum alloy, direct extrusion, force, pressure, regression

References.

1. Oyinbo, S., Ikumapayi, O., Jen, T., & Ismail, S. (2020). Experimental and numerical prediction of extrusion load at different lubricating conditions of aluminium 6063 alloy in backward cup extrusion. Engineering Solid Mechanics, 8(2), 119-130. https://doi.org/10.5267/j.esm.2019.10.003.

2. Luca, D., Sltineanu, L., Merticaru, V., Mihalache, A.M., Dodun,O., Ripanu, M.I., , & Panait, C.E. (2018). Finite element simulation and experimental investigation of cold forward extrusion process. MATEC Web of Conferences, 178, 02010. https://doi.org/10.1051/matecconf/201817802010.

3. Huang, S.H., Wu, Y., Xia, X.S., Zhao, Z.D., Chen, Q., & Shu,D.Y. (2019).Assessment of Cold Extrusion Effect on StressStrain Curves of Pure Copper Arc Parts Based on the Cosine Velocity Model. Strength of Materials, 51(4), 569-577. https://doi.org/10.1007/s11223-019-00102-8.

4. Ku, Tae-Wan (2020).A Combined Cold Extrusion for a Drive Shaft: A Parametric Study on Tool Geometry. Materials, 13(10), 2244. https://doi.org/10.3390/ma13102244.

5. Hou, H.-L., Zhang, G.-P., Xin, Ch., & Zhao, Yo.-Q. (2020).Numerical Simulation and Process Optimization of Internal Thread Cold Extrusion Process. Materials, 13(18), 3960. https://doi.org/10.3390/ma13183960.

6. A Nurul, M., & Syahrullail, S. (2017). A new approach for cold extrusion process: Dimples indentation on sliding contact surface and palm oil as an alternative lubricant. Scientia Iranica, 24(6), 2875-2886. https://doi.org/10.24200/sci.2017.4248.

7. Nanthakumar, S., Rajenthirakumar, D., & Avinashkumar, S. (2020). Influence of temperature on deformation behavior of copper during microextrusion process. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 234(9), 1797-1808. https://doi.org/10.1177/0954406219899114.

8. Miek, T., Borys, M., Czy, Z., Falkowicz, K., Kujawska, J., Kulisz,M., & Szala, M. (2017).The analysis of distributions of effective strain and flow stress in longitudinal sections of cold backward extruded copper cans for different punch-face shapes. ITM Web of Conferences, 15(10-11), 07014. https://doi.org/10.1051/itmconf/20171507014.

9. Al-Haidary, J., Haddad, J., Alfaqs, F., & Zayadin, F. (2021). Susceptibility of Aluminum Alloy 7075 T6 to Stress Corrosion Cracking. SAE International Journal of Materials and Manufacturing, 14(2). https://doi.org/10.4271/05-14-02-0013.

10. Mazorchuk, V., Naumova, I., Repyakh, S., & Sharkova, S. (2018). The stresses in the hollow cylindrical combined castings. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (3), 94-99. https://doi.org/10.29202/nvngu/2018-3/9.

11. Qamar, S.Z., Chekotu, J.Ch., & Qamar, S.B. (2019). Effect of Shape Complexity on Ram Pressure and Metal Flow in Aluminum Extrusion. JOM, 71(1). https://doi.org/10.1007/s11837-019-03748-6.

12. Berndt, N., Frint, P., & Wagner, M. (2018).Influence of Extrusion Temperature on the Aging Behavior and Mechanical Properties of an AA6060 Aluminum Alloy. Metals, 8(1), 51. https://doi.org/10.3390/met8010051.

13. Ikumapayi, Omolayo M., Oyinbo, Sunday T., Bodunde, Ojo P., Afolalu, Sunday A., Okokpujie, Imhade P., & Akinlabi, Esther T. (2018).The effects of lubricants on temperature distribution of 6063 aluminium alloy during backward cup extrusion process. Journal of Materials Research and Technology, 8(1), 1175-1187. https://doi.org/10.1016/j.jmrt.2018.08.006.

14. Lv, J., Hu, F., Cao, Q.D., Hong, X., Dong, X., & Zhang, X. (2017).Fabrication and Mechanical Characterization of Cold Extruded Aluminum Bronze Planar Microsprings. Journal of Materials Engineering and Performance, 26(6), 2919-2927. https://doi.org/10.1007/s11665-017-2688-5.

• < Prev
• Next >