Науковий вісник НГУ

The CAM-system technological capabilities of the cylindric worm lathe processing in the CNC lathes

• 
• 

User Rating:  / 0

PoorBest 

Details

Category: Geotechnical and mining mechanical engineering, machine building

Last Updated on 14 January 2015

Published on 14 January 2015

Hits: 5169

Authors:

S.O. Sivun, Public Joint Stock Company “Dnipropolymermash”, Software Engineer of the Department of Design of Control Programs, Dnepropetrovsk, Ukraine

V.V. Zil, Cand. Sci. (Tech.), Associate Professor, State Higher Educational Institution “National Mining University”, Deputy Head of the Department of Technology of Mining Engineering, Dnipropetrovsk, Ukraine

S.T. Patsera, Cand. Sci. (Tech.), Senior Research Fellow,State Higher Educational Institution “National Mining University”, Senior Lecturer of the Department of Technology of Mining Engineering, Dnipropetrovsk, Ukraine

Abstract:

Purpose. To reduce the time of development of the control programme for the multi-pass worm processing in the CNC lathes.

Methodology. The comparative analysis of the technological capabilities of the popular САМ-systems, and the special programme development and its experimental testing at one of the machine-building enterprise has been carried out.

Findings. We have raised the efficiency of programming of the control programme for the multi-pass coil cutting on the worm in the CNC lathe machines.A special macroprogramme for the cylindrical worm combined coil cutting scheme has been developed. The time required for development of the control programme for the multi-pass worm processing under the cutter in the CNC lathes has been reduced by seven times. The results are the most efficient for the worm combined coil cutting scheme. In the short-term outlook we plan: to develop the macroprogrammes for the double-enveloping worm processing in the CNC lathes; and to enhance the macroprogramme for the cylindrical worm processing.

Originality. We have determined and substantiated the ways of improvement of the computer-assisted design tools for the control programmes to turn the worm in the CNC lathe machines.

Practical value. We have simplified the requirements to the qualification level of the developer of the control programme so that CNC machine operator meets the requirements. The macroprogramme developed allows each CNC lathe machine operator to develop the combined multi-pass coil cutting along the cylindrical worm independently, without a programme engineer's participation. The offered approach has a significant value for the small and medium business enterprises along with the mining machine builders.

References:

1. Kuznetsov, Ye.Yu. and Yamnikov, A.S. (2010), “System of automated programming CNC lathes for multi-pass cutting of warm coils”, Izvestiya TulGU, Ser. Technical Sciences, Tula, Publishing house of the Tula state University, Vol. 1, pp. 97–104.

Кузнецов Е.Ю. Система автоматизированного программирования токарных станков с ЧПУ для многопроходного нарезания витков червяков / Е.Ю. Кузнецов, А.С. Ямников // Известия ТулГУ. Сер. „Техническиенауки“. -2010. -Вып. 1. – c. 97-104.

2. Kuznetsov, Ye.Yu. (2011), “Software for automated development of control programs for multi-pass cutting of coils worms CNC”, Izvestiya vuzov. Engineering, no.5. pp. 54–59.

Кузнецов Е.Ю. Программное обеспечение для автоматической разработки управляющих программ для многопроходного нарезания витков червяков на станках с ЧПУ // Известия вузов. Сер. „Машиностроение“. –2011. –№5. –с. 54–59.

3. Kuznetsov, Ye.Yu. (2012), “Select the direction of the cutting cutter when multi-pass cutting of coils worms”, Izvestiya TulGU, Ser. Technical Sciences, Tula, Publishing house of the Tula state University, Vol. 1, pp. 350–353.

Кузнецов Е.Ю. Выбор направления врезания резца при многопроходном нарезании витков червяков // Известия ТулГУ. Сер. „Технические науки“ –2012.–Вып. 1. –c. 350–353.

2014_6_sivun
2015-01-13  396.02 KB  1287

• < Prev
• Next >