The results of experimental studies of influence of variable parameters on the performance indicators of shock-centrifugal disintegrator
/ 9
- Details
- Category: Solid State Physics, Mineral Processing
- Last Updated on 20 March 2019
- Published on 03 March 2019
- Hits: 2825
Authors:
V.P.Nadutyy, Dr. Sc. (Tech.), Prof., orcid.org/0000-0002-2453-0351, Institute of Geotechnical Mechanics named by N.Polyakov of National Academy of Science of Ukraine, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Haddad Jamil, PhD, Assoc. Prof., orcid.org/0000-0003-3787-0010, Al-Balqa Applied University, Amman, Jordan, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
V.V.Sukharyev, Cand. Sc. (Tech.), orcid.org/0000-0002-7102-4734, Institute of Geotechnical Mechanics named by N.Polyakov of National Academy of Science of Ukraine, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
A.O.Loginova, Cand. Sc. (Tech.), orcid.org/0000-0002-7274-5330, Institute of Geotechnical Mechanics named by N.Polyakov of National Academy of Science of Ukraine, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Abstract:
Purpose. A study of the change in the magnitude of productivity of a shock-centrifugal disintegrator and the power output of its drive, with variations in the rotor speed with impactors in the chamber, the size and type of the initial grinded rock mass, and comparison of the technological performance of a single-chamber and two-chamber disintegrator.
Methodology. Laboratory research on bench equipment with subsequent processing of the experimental results obtained by computer programming.
Findings. It is established that in comparison with the single-chamber disintegrator in the new two-chamber design, the yield of the fine fraction of the rock mass is increased by 1.3‒1.7 times, and the productivity of the disintegrator and the reduction of grinding time of the rock mass are fixed.
Originality. For the first time, the character of the dependence of productivity of a two-chamber impact-centrifugal disintegrator and the power of its drive on its rotations and characteristics of the crushed rock mass is determined, and the distribution of classes of the crushed rock mass after grinding is established.
Practical value.The new design of the two-chamber impact-centrifugal disintegrator is efficient and promising because it divides the flow of rock mass into two chambers and thereby reduces the load on the rotor shaft, which increases its working time and the productivity of the disintegrator, and also reduces the grinding time of the rock mass. This allows recommending a new construction of a two-chamber impact-centrifugal disintegrator for use in industrial conditions.
References.
1. Bilenko, L. F., 2012. Priority areas for increasing the selectivity of minerals in the process of preparation of ore for enrichment. Vestnik NGU “KPI” [online], 59, pp. 3‒12. Available at: <https: //repository.kpi.kharkov.ua/handle/KhPI-Press/11681> [Accessed 7 November 2017].
2. Bulat, A. F., Dyrda, V. I. and Khokhotva, A. I., 2013. Techniques and technologies for the extraction, preparation and enrichment of mineral raw materials based on elastomeric materials. Geotechnical mechanics: Interdepartmental collection of scientific works IGTM NAS of Ukraine, 113, pp. 3‒43.
3. Bulat, A. F., Dyrda, V. I., Karnaukhov, V. G., Zvyagilsky, E. L. and Kobets, A. S., 2014. Applied mechanics of elastic hereditary media. In: Forced vibrations and dissipative heating of inelastic bodies. Vol. 4 (additional) Kiev: Naukova Dumka.
4. Dyrda, V. I., Sokol, S. P., Kalgankov, E. V., Kolbasin, V. A. and Tolstenko, A. V., 2013. Calculation of the durability of elastic-hereditary media under prolonged cyclic loading. Geotechnical mechanics: Interdepartmental collection of scientific works IGTM NAS of Ukraine, 108, pp. 111‒123.
5. Metodolog, 2008. The history of the centrifugal impact crusher [online]. Available at: <http://www.metodolog.ru/01340/01340.html> [Accessed 22 January 2018].
6. Lebedev, A. E. and Zaitsev, A. I., 2013. Mathematical description of the process of formation of dispersed streams. Basic research, 10‒15, pp. 3338‒3341.
7. Prabel, B., 2013. Analyse 3D des vibrations non-linéaires des rotors avec défauts, 11e Colloque National en Calcul des Structures [online]. Available at: <https://hal.archives-ouvertes.fr/hal-01722064/document> [Accessed 29 November 2017].
8. Naduty, V. P., Ziborov, K. A. and Loginova, A. O., Centrifugal percussion disintegrator. Ukraine. Pat. 116387, published 05/25/17.
9. Nadutyi, V. P., Sukharev, V. V. and Loginova, A. A., 2016. Justification of the efficiency of using centrifugal impact disintegrator that implements shear deformations during the destruction of the rock mass.Geotechnical mechanics: Interdepartmental collection of scientific works IGTM NAS of Ukraine, 131, pp. 26‒32.
10. Dyrda, V. I., Zozulya, R. P., Levitskiy, A. P. and Khmel’, I. V., 2014. Rubber linings of technological machines Monograph. Dnipro.
Archive