Optimal deviding of long products into rolled products of marketable length

User Rating:  / 0
PoorBest 

Authors:

A.S. Beshta, Corresponding Member of the National Academy of Science of Ukraine, Doctor of Technical Science, Professor, State Higher Educational Institution “National Mining University”, Vice-Rector for Scientific Affairs, Dnepropetrovsk, Ukraine.

M.Yu. Kuzmenko, The National Metallurgical Academy of Ukraine, Postgraduate Student, Dnepropetrovsk, Ukraine.

O.A. Boyko, State Higher Educational Institution “National Mining University”, Assistant Lecturer, Dnepropetrovsk, Ukraine.

A.S. Sokolova, State Higher Educational Institution “National Mining University”, Research Fellow, Dnepropetrovsk, Ukraine.

Abstract:

Purpose. To find patterns providing optimal yield of marketable products, cutting of long products at different steps of bar rolled products manufacture process.

Methodology. The solving of the problem of optimal cutting is based on the combinatorial analysis of possible options applied for making cutting plans aimed on dividing of long rolled products and comparing them by maximum output of marketable rolled products (products of required length) and their maximum value. First we have considered the deterministic case where the coordinates of the long rolled products edge are provided. In the second case, the location of the edge of long products is described by probabilistic characteristics.

Findings. The research showed that for optimization by the maximum output of marketable rolled products (products of required length) the choice of cutting plan is uncommon only in the second case where the location of the edge of long products is described by probabilistic characteristics; and the solution consists in selection of the coordinates of the first cut. When optimizing by the maximum value of the marketable rolled products the solution either coincides with the solution of the optimization problem by the maximum output of marketable rolled products (products of required length), or is a combination of cutting one part of long product to products of required length, and another, into the equal segments of marketable length.

Originality. We have established the general rules that ensure optimal cutting of long rolled products in various stages of the bar rolled products manufacture.

Practical value. The control of the long rolled products cutting process based on the received dependencies reduces the metal loss on shorts, and increases the yield of marketable products.

References:

1. Кузьменко А.Г. Производство мерного проката на непрерывных мелкосортных станах / Кузьменко А.Г. – М.: Металлургия, 1997. – 310 с.

Kuzmenko, A.G., (1997), Proizvodstvo mernogo prokata na nepreryvnykh melkosortnykh stanakh [Single-Length Rolled Products Production on Continuous Small Section Mill], Metallurgiya, Moscow, Russia.

2. Увеличение выхода мерного проката при производстве арматурных профилей / [А.Б. Юрьев, А.И. Погорелов,
И.С. Кузнецов и др.] – М.: Сталь, 2003. – № 2. – С. 63–64.

Yuryev, A.B., Pogorelov, A.I. and Kuznetsov, I.S., (2003), “Single-Length Rolled Products Output Increase at Rebar Production”, Stal, no.2, pp. 63–64.

3. Таха Х.А. Введение в исследование операций / Таха Х.А.; Перев. с англ. В.И. ТюптиМ.: Вильямс, 2001. – 912 с.

Taha, Hamdy A. (2001), Vvedenie v issledovanie operatsiy [Operations Research: an Introduction], Translated by V.I. Tyupti, Viliams, Moscow, Russia.

4. Ларичев О.И. Теория и методы принятия решений / Ларичев О.И. – М.: Логос. 2002. – 392 с.

Larichev, O.I., (2002), Teoriya i metody prinyatiya resheniy [Theory and Methods of Decision-Making], Logos, Moscow, Russia.

5. Подиновский В.В. Парето – оптимальные реше-ния многокритериальных задач / Подиновский В.В., Ногин В.Д. – М.: ФИЗМАТЛИТ, 2007. – 256 с.

Podinovskiy, V.V., (2007), Pareto – optimalnye reshe-niya mnogokriterialnykh zadach [Pareto - Optimal Solutions of Multi-Criteria Problems], FIZMATLIT, Moscow, Russia.

6. Кузьменко А.Г. Мелкосортные станы. Состояние, проблемы, перспективы / Кузьменко А.Г. – М.: Металлургия, 1996. – 368 с.

Kuzmenko A.G., (1996), Melkosortnye stany. Sostoyanie, problemy, perspektivy [Light Section Mills. Status, Problems and Prospects], Metallurgiya, Moscow, Russia.

7. Куваев В.Н. Рациональная организация резки пакетов мелкосортного проката на стационарных ножницах / В.Н. Куваев // Сталь. – 2001. – № 2. – С. 33–35.

Kuvaev, V.N., (2001), “The rational organization of cutting package hoop on stationary scissors”, Stal, no.2, pp. 33–35.

8. Куваев В.Н. Принципы оптимального раскроя мелкосортного проката на полосы / В.Н. Куваев // Науковий вiсник Національної гірничої академії України. – 2002. – № 2. – С. 88–91.

Kuvaev, V.N., (2002), “The principles of optimal cutting of small sections into strips”, Nаukovyi visnyk Nаtsionаlnoi hirnychoi аkаdеmii Ukrаiny, no.2, pp. 88–91.

9. Средства и системы автоматизации в горно-металлургическом комплексе / [Учитель А.Д., Ткаченко Г.И., Хижняк В.Я., Мохнатый А.В.] – К.: ВПК „Експрес-Поліграф“, 2013. – 184 с.

Uchitel, A.D., Tkachenko, G.I., Khizhnyak, V.Ya. and Mokhnatyi, A.V., (2013), Sredstva i sistemy avtomatizatsii v gorno-metallurgicheskom komplekse [Tools and Systems for Automation in the Mining and Metallurgical Complex], VPK “Ekspres-Polіgraf”, Kiev.

10. Определение координат характерных участков пакета прутков мелкосортного проката перед его порезкой на стационарных ножницах / [В.Н. Куваев, О.А. Бойко, М.Ю. Кузьменко, Е.Д. Иванова] // Теория и практика металлургии. – 2013. – №1. – С. 74–79.

Kuvaev, V.N., Boyko, O.O., Kuzmenko, M.Yu. and Ivanova, Ye.D., (2013), “Determining the origin of characteristic segments of package rods hoop before cutting by stationary scissors”, Teoriya i praktika metallurgii, no. 1, pp. 74–79.

Files:
2014_2_beshta
Date 2014-07-11 Filesize 296.76 KB Download 932
 

Visitors

6236829
Today
This Month
All days
1283
63506
6236829

Guest Book

If you have questions, comments or suggestions, you can write them in our "Guest Book"

Registration data

ISSN (print) 2071-2227,
ISSN (online) 2223-2362.
Journal was registered by Ministry of Justice of Ukraine.
Registration number КВ No.17742-6592PR dated April 27, 2011.

Contacts

D.Yavornytskyi ave.,19, pavilion 3, room 24-а, Dnipro, 49005
Tel.: +38 (056) 746 32 79.
e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
You are here: Home Archive by field of science Electrical engineering Optimal deviding of long products into rolled products of marketable length