- 1. Strength analysis of the model 918 wagon under non-typical bulk loads
- (Content №4 2024)
- ... Notes in Mechanical Engineering, 1, 133-142. Springer, Cham. https://doi.org/10.1007/978-3-030-77719-7_14. 8. Krol, O., & Sokolov, V. (2020). Modeling of Spindle Node Dynamics Using the Spectral ...
- Created on 28 August 2024
- 2. Creation of conceptual solutions for the manufacture of component freight wagons from composites
- (Content №5 2023)
- ... IV. DSMIE 2021. Lecture Notes in Mechanical Engineering, 1, 133-142. Springer, Cham. https://doi.org/10.1007/978-3-030-77719-7_14. 17. Krol, O., & Sokolov, V. (2020). Modeling of Spindle Node Dynamics ...
- Created on 27 October 2023
- 3. Load of a semi-car having the dismountable roof of composites
- (Content №1 2023)
- ... 5(9(101)), 16-27. https://doi.org/10.15587/1729-4061.2019.180197. 13. Krol, O., & Sokolov, V. (2020). Modeling of Spindle Node Dynamics Using the Spectral Analysis Method. Lecture Notes in Mechanical ...
- Created on 25 February 2023
- 4. Load of the wagon-platform for transportation of bulk cargoes
- (Content №5 2022)
- ... MATERIALE PLASTICE, 57(2), 140-151. https://doi.org/10.37358/MP.20.2.5360. 9. Krol, O., & Sokolov, V. (2020). Modeling of Spindle Node Dynamics Using the Spectral Analysis Method. Lecture Notes in ...
- Created on 30 October 2022
- 5. Methods for determining the efficiency of the grinding process
- (Contens №5 2020)
- ... N. K. J., Fedorovich, V., Pyzhov, I., Markopoulosc, A. P., & Klimenkod, V. (2017). Theoretical Analysis of the Contact Area between Grinding Wheel Surface and Workpiece in Flat Face Grinding with Spindle ...
- Created on 30 October 2020
- 6. Development and research of thеrmоplаstiс methods for hardening details
- (Contens №2 2020)
- ... Methodology. Experimental studies on the influence of the temperature factor on the hardening process were carried out at a specialized facility developed at the Department of Engineering and Woodworking Technology of CNUT (Chernihiv National University of Technology). The three-roller pneumatic device was mounted on a support of the lathe-screw machine model 1K62. Workpieces were mounted on a special mandrel in a three-jaw chuck. The spindle speed was set using an electronic tachometer; the pressure on the rollers was recorded by a pressure gauge. Before the rolling, the workpiece was kept in a laboratory electric furnace, the preheat temperature was recorded by a logometer. Since the surface quality of surface plastic deformation (SPD) treatment with heating depends on a large number of factors, a central second-order rotatable composite layout was used to obtain the multifactor model. On the basis of a priori information and the results of the previous experiments, the feed (S, mm/rev), pressure (P, H) and preheat temperature (T, °C) were taken as factors determining the process. The surface layer hardness was taken as the initial parameter. ...
- Created on 10 May 2020
- 7. Energy optimization of a hoisting engine acceleration
- (Power Supply Technologies)
- ... Research and General Science, 4(2), 91-96. 4. Zhen-liang, Y., & Wei-min, L. (2011). CAE Optimization Design of Mine Hoist Spindle Device. Advanced Materials Research, 299-300, 878-882. DOI: 10.4028/www.scientific.net/AMR.299-300.878. ...
- Created on 26 October 2019
- 8. Information-measuring complex for the research on trajectories of spindle with hydrostatical bearings
- (Geotechnical and mining mechanical engineering, machine building)
- ... of the parameters of movement trajectories of the spindle on hydrostatic bearings, based on the use of high-precision laser triangulation position sensors and digital signal processing. Methodology. ...
- Created on 08 February 2016