- 1. Rotor configuration for improved working characteristics of LSPMSM in mining applications
- (Content №3 2024)
- ... pumping loads to improve the efficiency of electricity use in mining. Methodology. The article uses analytical methods and simulation methods on Ansys/Maxwell software and conducts a laboratory test ...
- Created on 28 June 2024
- 2. CFD-modeling of critical deviations of combustion processes in pulverized coal boilers. Part 1. Construction of the TPP-210A boiler calculation model
- (Content №2 2024)
- ... CFD models of the boiler unit in the ANSYS-Fluent software complex with the determination of the relevant characteristics of the boiler. Findings. Finite-element CFD models were developed according to ...
- Created on 01 May 2024
- 3. Modeling pH changes and electrical conductivity in surface water as a result of mining activities
- (Content №1 2024)
- ... coal mine and environs affected by mining activities. Methodology. The research utilizes a combination of in-situ measurement, laboratory analysis, modeling technique using Ansys Workbench and Linear ...
- Created on 29 February 2024
- 4. The influence of the impeller design features on the combined operating process of the torque-flow pump
- (Content №2 2023)
- ... out using the ANSYS CFX software package. The integral parameters of the researched pump were determined in order to build the integral characteristics. Findings. The structure of the general flow and ...
- Created on 28 April 2023
- 5. Selective non-catalytic reduction of nitrogen oxides in the production of iron ore pellets
- (Content №1 2022)
- ... Methodology. The research results have been obtained using CFD-modeling in the ANSYS Fluent software package. To model this process, a computational domain is constructed, which corresponds in size to ...
- Created on 25 February 2022
- 6. Co-firing of gas coal dust fine particles and synthetic peat gas. Part 1. Simulation of processes of steam-air gasification of peat in a fixed bed and combustion of dust and gas mix in a stream
- (Content №6 2021)
- ... to calculate the peat gasification process. To study the process of burning a binary blend, ANSYS FLUENT package was used. Findings. A model of solid fuel gasification in a fixed bed has been ...
- Created on 29 December 2021
- 7. Analytical and experimental assessment of screw centrifugal pump at improving its design
- (Content №4 2021)
- ... ANSYS Workbench. The Bulletin of Voronezh State Technical University, 13(2), 29-32. 11. Sulinov, A.V., Shabliy, L.S., & Zubanov, V.M. (2015). Methods of modeling the work process of hydrogen screw-centrifugal ...
- Created on 23 August 2021
- 8. Recirculation power in the balance of hydraulic losses of centrifugal pump
- (Contens №5 2020)
- ... using the ANSYS CFX software. Findings. The dynamics of changes in the integral parameters of the operational process of a centrifugal pump D2000-100-2 at flow rates that deviate from optimal (Qopt) ...
- Created on 30 October 2020
- 9. The analytic-field method for calculating the squirrel-cage induction motor parameters
- (Contens №3 2020)
- ... of copyright registration for work No. 83322, Ukraine. 11. Tikhonova, O., Malygin, I., & Plastun, A. (2017). Electromagnetic calculation for induction motors of various designs by ANSYS Maxwell. ...
- Created on 02 July 2020
- 10. Identification of material parameters for numerical simulation of the behavior of rocks under true triaxial conditions
- (Solid State Physics, Mineral Processing)
- ... on the behavior of rocks in the true triaxial stress field using the experimental method and numerical mathematical modeling are presented. Modeling is conducted by the finite element method in Ansys Inc ...
- Created on 29 October 2018
- 11. Mathematical modeling of the operating process of the engine and means of increasing service life of vehicles
- (Geotechnical and mining mechanical engineering, machine building)
- ... Research Journal, 6‒48(2), pp. 81‒84. DOI: 10.18454/IRJ.2016.48.027. 5. Lukachev, S., Biryuk, V. and Gorshkalev, A., 2014. Using Ansys Fluent to Study Gas-Dynamic and Thermal Processes in Small-Sized ...
- Created on 03 July 2018
- 12. Numerical studies on the effect of impeller outlet width on characteristic curve slope of the centrifugal impeller
- (Geotechnical and mining mechanical engineering, machine building)
- ... експерименту і числового моделювання / Лінг Зоу, Вейдонг Ши // Досягнення в галузі машинобудування. – 2013. – №5. – С. 41–48. 7. ANSYS CFX 13.0 Solver Theory. Release 13.0.[online] Available at: ...
- Created on 04 August 2016
- 13. Effectiveness of thermomechanical calibration and determination of residual stresses in the shell nose cone of Cyclone-4
- (Geotechnical and mining mechanical engineering, machine building)
- Authors: D.G. Sherstiuk, Oles Honchar Dnepropetrovsk National University, postgraduate student, Physics and Engineering Department, Dnipropetrovsk, Ukraine. A.V. Kulik, Cand. Sci. (Tech.), Oles Honchar ...
- Created on 21 March 2014
- 14. Зміст / Содержание № 11 (2005)
- (2005)
- ... Е.В. Разработка модели резинотросового каната в многослойной намотке на основе универсального пакета конечно-элементного моделирования Ansys/ED 6.1 Полушина М.В., Жупиев АЛ., Панченко ...
- Created on 13 December 2012