Alternative uses for crushed stone products generated to meet the raw material needs of asphalt production in Hungary
/ 0
- Details
- Category: Content №5 2023
- Last Updated on 27 October 2023
- Published on 30 November -0001
- Hits: 2379
Authors:
L.Ézsiás, orcid.org/0009-0003-2637-2830, Széchenyi István University, Győr, Hungary
S.Fischer*, orcid.org/0000-0001-7298-9960, Széchenyi István University, Győr, Hungary
* Corresponding author e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2023, (5): 066 - 071
https://doi.org/10.33271/nvngu/2023-5/066
Abstract:
In Hungary, quarries that produce stone products for wearing courses of asphalt pavements also produce a significant amount of 0/4, 0/8 and 4/8 mm fractions. Because of Hungary’s pavement design and asphalt production practices, these fractions do not have a suitable market and can thus be sold on alternative markets.
Purpose. To demonstrate the feasibility of using crushed fractions of 0/4 and 0/8 mm in the protection and base layers of asphalt pavements instead of sandy gravel with 0/22 mm fraction.
Methodology. The CBR method was applied to evaluate the comparability of characteristics such as particle size distribution and load-bearing capacity. The combination of the Proctor and CBR tests allowed someone to compare the expected technological characteristics of the dominant and alternative aggregate types, such as their sensitivity to water and load-bearing capacity.
Findings. The results demonstrated that the performance characteristics of conventionally used sandy gravel with a size of 0/22 mm can be achieved and exceeded by crushed material with much smaller maximum grain sizes – i.e., 0/4 and 0/8 mm.
Originality. The paper presents an original study that contradicts the industry’s actual decline of crushed stone (0/4 and 0/8 mm fractions) for asphalt pavement protection layers. The potential effectiveness and functionality of the proposed coating are demonstrated through convincing tests, and thus new data and insights are introduced into the Hungarian construction industry’s practice.
Practical value. The test results greatly helped in achieving the high demands of the private industrial project by proposing an alternative variant of crushed stone of 0/8 mm fraction rather than the originally planned dominant sand and gravel material. The asphalt paving experience on this site clearly demonstrated the viability of the alternative aggregate option for Hungarian roads.
Keywords: asphalt pavement, sand and gravel products, crushed stone, alternative raw materials, load-bearing capacity, Proctor tests, CBR
References.
1. Fischer, S., & Szürke, S. K. (2023). Detection process of energy loss in electric railway vehicles. Facta Universitatis, Series: Mechanical Engineering, 21(1), 81-99. https://doi.org/10.22190/FUME221104046F.
2. Gáspár, L., Horvát, F., & Lublóy, L. (2011). Lifetime of transport infrastructure facilities. Universitas-Győr Nonprofit Kft., Győr, 323 p.
3. Kurhan, M. B., Kurhan, D. M., Husak, M. A., & Hmelevska, N. (2022). Increasing the efficiency of the railway operation in the specialization of directions for freight and passenger transportation. Acta Polytechnica Hungarica, 19(3), 231-244. https://doi.org/10.12700/APH.19.3.2022.3.18.
4. Taran, I., & Litvin, V. (2018). Determination of rational parameters for urban bus route with combined operating mode. Transport Problems, 13(4), 157-171. https://doi.org/10.20858/tp.2018.13.4.14.
5. Saukenova, I., Oliskevych, M., Taran, I., Toktamyssova, A., Aliakbarkyzy, D., & Pelo, R. (2022). Optimization of schedules for early garbage collection and disposal in the megapolis. Eastern-European Journal of Enterprise Technologies, 1(3-115), 13-23. https://doi.org/10.15587/1729-4061.2022.251082.
6. Sładkowski, A., Utegenova, A., Kolga, A. D., Gavrishev, S. E., Stolpovskikh, I., & Taran, I. (2019). Improving the efficiency of using dump trucks under conditions of career at open mining works. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (2), 36-42. https://doi.org/10.29202/nvngu/2019-2/8.
7. Czinder, B., Vásárhelyi, B., & Török, Á. (2021). Long-term abrasion of rocks assessed by micro-Deval tests and estimation of the abrasion process of rock types based on strength parameters. Engineering Geology, 282, 105996. https://doi.org/10.1016/j.enggeo.2021.105996.
8. Mussin, A., Imashev, A., Matayev, A., Abeuov, Ye., Shaike, N., & Kuttybayev, A. (2023). Reduction of ore dilution when mining low-thickness ore bodies by means of artificial maintenance of the mined-out area. Mining of Mineral Deposits, 17(1), 35-42. https://doi.org/10.33271/mining17.01.035.
9. Zholmagambetov, N., Khalikova, E., Demin, V., Balabas, A., Abdrashev, R., & Suiintayeva, S. (2023). Ensuring a safe geomechanical state of the rock mass surrounding the mine workings in the Karaganda coal basin, Kazakhstan. Mining of Mineral Deposits, 17(1), 74-83. https://doi.org/10.33271/mining17.01.074.
10. Károlyfi, K. (2017). The effect of saturation degree of cement paste on fair-faced concrete surfaces. Építöanyag (Online), (2), 55. https://doi.org/10.14382/epitoanyag-jsbcm.2017.10.
11. Kuchak, A. J. T., Marinkovic, D., & Zehn, M. (2020). Finite element model updating – Case study of a rail damper. Structural Engineering and Mechanics, 73(1), 27-35. https://doi.org/10.12989/sem.2020.73.1.027.
12. Kuchak, A. J. T., Marinkovic, D., & Zehn, M. (2021). Parametric Investigation of a Rail Damper Design Based on a Lab-Scaled Model. Journal of Vibration Engineering and Technologies, 9(1), 51-60. https://doi.org/10.1007/s42417-021-00341-7.
13. Szalai, S., & Dogossy, G. (2021). Speckle pattern optimization for DIC technologies. Acta Technica Jaurinensis, 14(3), 228-243. https://doi.org/10.14513/actatechjaur.00573.
14. Taran, I., & Klymenko, I. (2017). Analysis of hydrostatic mechanical transmission efficiency in the process of wheeled vehicle braking. Transport Problems, 12(Special Edition), 45-56. https://doi.org/10.20858/tp.12.se.4.
15. Fischer, S., Harangozó, D., Németh, D., Kocsis, B., Sysyn, M., Kurhan, D., & Brautigam, A. (2023). Investigation of Heat-Affected Zones of Thermite Rail Weldings. Facta Universitatis, Series: Mechanical Engineering (accepted manuscript as an article in Online First stage). https://doi.org/10.22190/FUME221217008F.
16. Kocsis Szürke, S., Kovács, G., Sysyn, M., Liu, J., & Fischer, S. (2023). Numerical Optimization of Battery Heat Management of Electric Vehicles. Journal of Applied and Computational Mechanics, 9(4), 1076-1092. https://doi.org/10.22055/jacm.2023.43703.4119.
17. SNAP-SEE project: Sustainable Aggregates Planning in South East Europe. Retrieved from http://www.snapsee.eu.
18. 100-year-old Hungarian Geological Institute (2023, August 27). Geological map of Hungary. Retrieved from https://gallery.hungaricana.hu/hu/SzerencsKepeslap/1320146/?img=0.
19. Sustainable roads – Optimizing sustainable roads on a national economic level, Professional publication, by the Hungarian Road Administration (2013). Retrieved from https://adoc.pub/fenntarthato-utak-fenntarthato-utgy-magyar-kzut-nonprofit-zr.html.
20. Fladvad, M., & Ulvik, A. (2021). Large-size aggregates for road construction – a review of standard specifications and test methods. Bulletin of Engineering Geology and the Environment, 80(12), 8847-8859. https://doi.org/10.1007/s10064-019-01683-z.
21. Ézsiás, L. (2009). Analyzing the reliability of test methods for earthworks. Közlekedésépítési Szemle, 59(2), 15-23. Retrieved from https://szemle.pms2000.hu/docs/2009_02.pdf.
22. Budiarto, A. (2018). The influence of replacement of course aggregate material with crushed stone to the CBR value on Aggregate Class B. AIP Conference Proceedings (Human-Dedicated Sustainable Product and Process Design: Materials, Resources, and Energy: Proceedings of the 4th International Conference on Engineering, Technology, and Industrial Application (ICETIA) 2017), pp. 13-14, December 2017, Surakarta, Indonesia, 1977(1), 020033. https://doi.org/10.1063/1.5042889.
23. Satyanarayana, P. V. V., Prem Teja, R., Harshanandan, T., & Lewis Chandra, K. (2013). A study on the use of crushed stone aggregate and crusher dust mixes in flexible pavements. International Journal of Scientific & Engineering Research, 4(11), 1126.
24. Hungarian Standards Institute (1989). Bearing capacity test on pavement structures. Plate bearing test (MSZ 2509-3:1989). Retrieved from https://ugyintezes.mszt.hu/webaruhaz/szabvany-adatok?standard=90404.
25. European Committee for Standardization (2012). Unbound and hydraulically bound mixtures. Part 2: Test methods for laboratory reference density and water content. Proctor compaction (EN 13286-2:2010/AC:2012). Retrieved from https://infostore.saiglobal.com/en-us/standards/en-13286-2-2010-ac-2012-327593_saig_cen_cen_754498.
26. European Committee for Standardization (2021). Unbound and hydraulically bound mixtures. Part 47: Test method for the determination of California bearing ratio, immediate bearing index and linear swelling (EN 13286-47:2021). Retrieved from https://infostore.saiglobal.com/en-gb/standards/en-13286-47-2021-333354_saig_cen_cen_3073508.
27. European Committee for Standardization (2012). Tests for geometrical properties of aggregates – Part 1: Determination of particle size distribution – Sieving method (EN 933-1:2012). Retrieved from https://infostore.saiglobal.com/en-gb/standards/EN-933-1-2012-330012_SAIG_CEN_CEN_759336.
28. Magyar Közút Nonprofit Zrt. (2007). General geotechnical rules for the establishment of public roads (e-UT 06.02.11). Retrieved from https://ume.kozut.hu/dokumentum/190.
Newer news items:
- Controlling as an enterprise management tool in the digital economy - 27/10/2023 19:19
- Research on an eco-safe filtration plant for wastewater treatment made of natural raw materials - 27/10/2023 19:19
- Problems of prosecution for crimes against environmental security in the conditions of martial state - 27/10/2023 19:19
- The legal mechanism for environmental protection in Ukraine - 27/10/2023 19:19
- Radionuclide content in vegetation and soils in the impact zone of the railway track - 27/10/2023 19:19
- Creation of conceptual solutions for the manufacture of component freight wagons from composites - 27/10/2023 19:19
- Liquefaction of industrial zone against earthquake loading using laboratory and field measurements - 27/10/2023 19:19
- Optimization mathematical model of a contact air cooler for a mine turbocompressor - 27/10/2023 19:19
- Principles of transport means maintenance optimization: equipment cost calculation - 27/10/2023 19:19
- Combustion and detonation of paste fuel of rocket engine - 27/10/2023 19:19
Older news items:
- Evaluation of coal mines’ rock mass gas permeability in the equivalent stress zone - 27/10/2023 19:19
- Geometric modelling of face processing surfaces by planetary executive devices of tunnelling machines - 27/10/2023 19:19
- Influence of drilling mud pulsations on well cleanout efficiency - 27/10/2023 19:19
- Reducing the formation of asphaltene deposits and increasing the flow rates of oil wells - 27/10/2023 19:19
- Geophysical indicators of rare-metal ore content of Akmai-Katpar ore zone (Central Kazakhstan) - 27/10/2023 19:19
- Prospects for the detection of structures with hydrocarbon deposits along the geotraverse in the Shu-Sarysu sedimentary basin - 27/10/2023 19:19
- Predicted resource assessment of Central Kazakhsta ore districts based on airborne geophysical methods - 27/10/2023 19:19
- Influence of the geotectonic regime on property formation of coal in the northern edges of the Donetsk basin - 27/10/2023 19:19
- Structure and interpretation of the anomalous magnetic field of the South Turgay petroleum region - 27/10/2023 19:19
