Mathematical modeling of a magnetic gear for an autonomous wind turbine
- Details
- Category: Content №2 2024
- Last Updated on 01 May 2024
- Published on 30 November -0001
- Hits: 2579
Authors:
M.A.Kovalenko, orcid.org/0000-0002-5602-2001, National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”, Kyiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
I.Ya.Kovalenko*, orcid.org/0000-0003-1097-2041, National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”, Kyiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
I.V.Tkachuk, orcid.org/0000-0002-5717-2458, National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”, Kyiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
A.G.Harford, orcid.org/0000-0002-9898-6474, National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute”, Kyiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
D.V.Tsyplenkov, orcid.org/0000-0002-0378-5400, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
* Corresponding author e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2024, (2): 088 - 095
https://doi.org/10.33271/nvngu/2024-2/088
Abstract:
Purpose. Development of a two-dimensional field mathematical model of a magnetic gearbox operating as part of a low-power wind turbine for the purpose of evaluating its parameters and characteristics and optimizing geometric parameters from the point of view of electromagnetic torque pulsations.
Methodology. To carry out the research, the methods of the general theory of electromechanical energy converters, numerical methods of mathematical modeling based on the finite element method, numerical solution of nonlinear differential equations, and methods of spectral analysis to estimate pulsations of the electromagnetic torque were used in the work.
Findings. The paper developed a two-dimensional numerical field mathematical model of a magnetic gearbox for an autonomous wind turbine. The model was developed to evaluate the parameters and characteristics of the magnetic gear, as well as to evaluate the influence of the design parameters on the magnitude of the electromagnetic torque and the magnitude of the pulsations of the electromagnetic torque. The effect of the configuration of permanent magnets, the parameters of the ferromagnetic inserts of the magnetic flux modulator and the size of the air gap was investigated in the paper. The obtained results show that there is an optimal configuration of permanent magnets and ferromagnetic elements of the magnetic flux modulator in which the maximum electromagnetic torque and minimum pulsations are achieved. Changing the parameters of the magnetic system affects the dynamics of the magnetic gear, its reliability and efficiency, therefore configuration optimization is an important task in the design, development and implementation of such systems.
Originality. A two-dimensional field mathematical model of the magnetic gear has been developed, which makes it possible to estimate the change in its parameters and characteristics when the geometric dimensions change. This allows investigating the influence of various parameters of the magnetic system, such as the height of the permanent magnets and the width of the ferromagnetic inserts, on the electromagnetic torque. This makes it possible to obtain the optimal configuration of the system to achieve the optimal value of the torque and minimal pulsations and to determine the regularity of the change of the electromagnetic torque and other parameters of the gearbox under different operating modes in the future.
Practical value. The simulation results indicate the prospects of industrial implementation of magnetic gaers as part of a wind power plant, and the obtained research results indicate the possibility of optimizing the design of magnetic gears in order to increase their reliability and efficiency.
Keywords: magnetic gear, permanent magnets, wind energy, wind-power engineering, electromagnetic torque, torque pulsations
References.
1. Golovko, V., Ostroverkhov, M., Kovalenko, M., Kovalenko, I., & Tsyplenkov, D. (2022). Mathematical simulation of autonomous wind electric installation with magnetoelectric generator. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (5), 74-79. https://doi.org/10.33271/nvngu/2022-5/074.
2. Chumack, V., Bazenov, V., Tymoshchuk, O., Kovalenko, M., Tsyvinskyi, S., Kovalenko, I., & Tkachuk, I. (2021). Voltage stabilization of a controlled autonomous magnetoelectric generator with a magnetic shunt and permanent magnet excitation. Eastern-European Journal of Enterprise Technologies, 6(5(114), 56-62. https://doi.org/10.15587/1729-4061.2021.246601.
3. Ostroverkhov, M., Chumack, V., Kovalenko, M., & Kovalenko, I. (2022). Development of the control system for taking off the maximum power of an autonomous wind plant with a synchronous magnetoelectric generator. Eastern-European Journal of Enterprise Technologies, 4(2(118), 67-78. https://doi.org/10.15587/1729-4061.2022.263432.
4. Beshta, O.O., Beshta, O.S., Beshta, D., Tkachenko, S., Khalaimov, T., & Skliar, D. (2023). Technologies for Increasing the Energy Efficiency of Electric Vehicles. IEEE 5 th International Conference on Modern Electrical and Energy System (MEES), 1-5. https://doi.org/10.1109/MEES61502.2023.10402470.
5. Jian, H., Yao, L., Li, W.-J., & Zhang, J. (2017). Design and realization of a novel magnetic nutation drive for industry robotic wrist reducer. Industrial Robot: An International Journal, 44, 58-63. https://doi.org/10.1108/IR-04-2016-0130.
6. Yu, W., Wang, C., & Xu, T. (2019). The design method of a novel magnetic suction gear reducer. IOP Conference Series: Materials Science and Engineering, 504, 012093. https://doi.org/10.1088/1757-899X/504/1/012093.
7. Hasanpour, S., Johnson, M., Gardner, M., & Toliyat, H. (2022). Cycloidal Reluctance Magnetic Gears for High Gear Ratio Applications. IEEE Transactions on Magnetics, 58(6), 1-10, 8001210. https://doi.org/10.1109/TMAG.2022.3163419.
8. Gardner, M., Praslicka, B., Johnson, M., & Toliyat, H. (2021). Optimization of Coaxial Magnetic Gear Design and Magnet Material Grade at Different Temperatures and Gear Ratios. IEEE Transactions on Energy Conversion, 36(3), 2493-2501. https://doi.org/10.1109/TEC.2021.3054806.
9. Dai, B., Nakamura, K., Suzuki, Y., Tachiya, Y., & Kuritani, K. (2022). Cogging Torque Reduction of Integer Gear Ratio Axial-Flux Magnetic Gear for Wind-Power Generation Application by Using Two New Types of Pole Pieces. IEEE Transactions on Magnetics, 58(8), 1-5, 8002205. https://doi.org/10.1109/TMAG.2022.3159002.
10. Chumak, V., Ostrovierkhov, M., Kovalenko, M., Holovko, V., & Kovalenko, I. (2022). Correction of the output power of the generator of the multiplierless wind power plant at discrete and random values of the wind speed. Bulletin of NTU “KhPI”. Series: Problems of improvement of electric machines and devices. Theory and practice, 2(8), 39-46. https://doi.org/10.20998/2079-3944.2022.2.07.
11. Chumak, V., Kovalenko, M., Tkachuk, I., & Kovalenko, I. (2022). Comparison of synchronous generators for an autonomous gasoline installation. Bulletin of NTU “KhPI”. Series: Problems of improvement of electric machines and devices. Theory and practice, 2(8), 32-38. https://doi.org/10.20998/2079-3944.2022.2.06.
12. Moghimi, A., Aliabadi, M., & Farahani, H. (2022). Triple-speed coaxial magnetic gear for wind turbine applications: introduction and comprehensive analysis. COMPEL – The international journal for computation and mathematics in electrical and electronic engineering, 41(4). https://doi.org/10.1108/Compel-01-2022-0001.
13. Aiso, K., Akatsu, K., & Aoyama, Y. (2021). A Novel Flux-Switching Magnetic Gear for High-Speed Motor Drive System. IEEE Transactions on Industrial Electronics, 68(6), 4727-4736. https://doi.org/10.1109/TIE.2020.2988230.
14. Ruiz-Ponce, G., Arjona, M., Hernandez, C., & Escarela-Perez, R. (2023). A Review of Magnetic Gear Technologies Used in Mechanical Power Transmission. Energies, 16, 1721. https://doi.org/10.3390/en16041721.
15. Wang, Y., Filippini, M., Bianchi, N., & Alotto, P. (2019). A Review on Magnetic Gears: Topologies, Computational Models, and Design Aspects. IEEE Transactions on Industry Applications, 55(5), 4557-4566. https://doi.org/10.1109/TIA.2019.2916765.
16. Nielsen, S., Wong, H., Baninajar, H., Bird, J., & Rasmussen, P. (2022). Pole and Segment Combination in Concentric Magnetic Gears: Vibrations and Acoustic Signature. IEEE Transactions on Energy Conversion, 37(3), 1644-1654. https://doi.org/10.1109/TEC.2022.3151654.
17. Ding, J., Yao, L., Xie, Z., Wang, Z., & Chen, G. (2022). A Novel 3-D Mathematical Modeling Method on the Magnetic Field in Nutation Magnetic Gear. IEEE Transactions on Magnetics, 58(5), 1-10. https://doi.org/10.1109/TMAG.2022.3158973.
18. Syam, S., Kurniati, S., & Ramang, R. (2022). Design and Characteristics of Axial Magnetic Gear Using Rectangular. Magnet. https://doi.org/10.31219/osf.io/5c724.
19. Mizuana Yuma, Nakamura Kenji, Suzuki Yuma, Oishi Yuhei, Tachiya Yuichi & Kuritani Kingo (2020). Development of spoke-type IPM magnetic gear. International Journal of Applied Electromagnetics and Mechanics, 64, 771-778. https://doi.org/10.3233/JAE-209389.
20. Cansiz, A., & Akyerden, E. (2019). The use of high temperature superconductor bulk in a coaxial magnetic gear. Cryogenics. https://doi.org/98.10.1016/j.cryogenics.2019.01.008.
21. Tzouganakis, P., Gakos, V., Kalligeros, C., Papalexis, C., Tsolakis, A., & Spitas, V. (2022). Torque ripple investigation in coaxial magnetic gears. MATEC Web of Conferences, 366. https://doi.org/01004.10.1051/matecconf/202236601004.
22. Misron, N., Mohd Saini, L., Aris, I., Vaithilingam, C. A., & Tsuyoshi, H. (2020). Simplified Design of Magnetic Gear by Considering the Maximum Transmission Torque Line. Applied Sciences. https://doi.org/10.3390/app10238581.
23. Ishikawa, S., & Todaka, T. (2020). Transient-operation phenomena of a magnetic reducer analyzed with the time-stepping FEM. 23 rd International Conference on Electrical Machines and Systems, 1898-1901. https://doi.org/10.23919/ICEMS50442.2020.9291208.
24. Tzouganakis, P., Gakos, V., Kalligeros, C., Tsolakis, A., & Spitas, V. (2022). Fast and efficient simulation of the dynamical response of coaxial magnetic gears through direct analytical torque modelling. Simulation Modelling Practice and Theory, 123. https://doi.org/10.1016/j.simpat.2022.102699.
25. Kastawan, I., & Rusmana (2016). Pengujian pembangkitan tegangan generator axial-flux permanent magnet (AFPM) tiga-fasa ganda. Jurnal Teknik Energi, 6, 503-509. https://doi.org/10.35313/energi.v6i2.1713.
26. Asfirane, S., Hlioui, S., Amara, Y., & Gabsi, M. (2019). Study of a Hybrid Excitation Synchronous Machine: Modeling and Experimental Validation. Mathematical and Computational Applications, 24(2), 34. https://doi.org/10.3390/mca24020034.
Newer news items:
- Legal regulation of labor of internally displaced persons in Ukraine - 01/05/2024 16:32
- Personnel development under digital economy conditions - 01/05/2024 16:32
- Economic security of the industrial enterprise in the frameworks of business process reengineering - 01/05/2024 16:32
- Determining the parameters of the functioning for a nonlinear ballistic system in a real external environment - 01/05/2024 16:31
- The research of industrial production dynamics based on the tools of chaos theory - 01/05/2024 16:31
- Express bus mode as an alternative way of improving the environmental safety of cities - 01/05/2024 16:31
- Eco-friendly biosorbent based on local raw material: application to dye removal - 01/05/2024 16:31
- Basics of calculation of a two-circuit air purification system for polydisperse dust - 01/05/2024 16:31
- Electric vehicle energy consumption taking into account the route topology - 01/05/2024 16:31
- Cable line equivalent circuit parameters determination using the instantaneous power components - 01/05/2024 16:31
Older news items:
- Characteristics of elasticity, frequency, and stability of plate connecting assemblies for vibrating machines - 01/05/2024 16:31
- A hybrid ICEEMDAN and OMEDA-based vibrodiagnosis method for the bearing of rolling stock - 01/05/2024 16:31
- Drilling wells taking into account the dynamic properties of rocks - 01/05/2024 16:31
- Gold recovery from waste fine carbon using acetone as solvent (Amesmessa gold mine, Algeria) - 01/05/2024 16:31
- CFD-modeling of critical deviations of combustion processes in pulverized coal boilers. Part 1. Construction of the TPP-210A boiler calculation model - 01/05/2024 16:31
- Influence of hot plastic deformation on properties of the carbon steel - 01/05/2024 16:31
- Container technology for transporting rock masses in quarries - 01/05/2024 16:31
- Assessment of the state of the rock mass around the crosscuts under additional deformation disturbances - 01/05/2024 16:31
- Influence of relaxation on filtering microflows under harmonic action on the layer - 01/05/2024 16:31
- Formation of prospecting criteria for copper-porphyry deposits based on the construction of reference models - 01/05/2024 16:31