Application of the stereomicrophotogrammetric method for the complex study of the Al-Cu-Mg alloys system
- Details
- Category: Content №4 2023
- Last Updated on 28 August 2023
- Published on 30 November -0001
- Hits: 2155
Authors:
A.V.Uhl, orcid.org/0000-0002-5249-0828, Lesya Ukrainka Volyn National University, Lutsk, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
O.V.Melnyk*, orcid.org/0000-0002-5429-4038, Lesya Ukrainka Volyn National University, Lutsk, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Yu.A.Melnyk, orcid.org/0000-0001-5186-7032, Lutsk National Technical University, Lutsk, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
* Corresponding author e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2023, (4): 056 - 061
https://doi.org/10.33271/nvngu/2023-4/056
Abstract:
Purpose. To combine the stereophotogrammetric method for processing fracture surface images at the micro level with the results of a series of mechanical and metal fractographic studies with precision methods for scanning electron microscopy (SEM) and energy dispersive analysis (EDX) in order to determine the peculiarities and general laws of the fracture process of Al-Cu-Mg test samples.
Methodology. In this work, the mechanical properties of Al-Cu-Mg samples after mild (recrystallization) annealing and subsequent natural aging and a sample without heat treatment were experimentally determined. At the next stage, SEM-stereomicrofractographic research on fractures and their three-dimensional reconstruction from the obtained stereo images were performed. EDX studies have been performed on various parts of the samples to determine the distribution of mass percentages of elements in the study areas. A comprehensive methodology for experimental studies of Al-Cu-Mg alloys was used in this work to obtain qualitative and quantitative information on the microstructure of fractures, which consisted of the following steps: determination of the mechanical properties of samples by traditional methods of macro- and microanalysis; study on stereopairs of the microstructure of fractures by the stereophotogrammetric method; identification of the chemical composition and structure of matrix precipitation particles by energy dispersive X-ray spectroscopy (EDX analysis).
Findings. Our experiments have shown that with an increase in the time of natural aging, the hardness increases slowly and reaches a maximum hardness of 127 Hv30 after 97 hours, which does not decrease subsequently. After natural hardening, the average fracture strength increases to Rm 440.3 with a relative elongation of 21.8 %. Mechanical tests have shown that the tensile strength increases with the hardness value and, in contrast, the toughness decreases. The energy required to fracture the sample is 16 J, followed by transcrystalline cellular fracture. The precipitates have a diameter of approximately 2.5–3 microns.
Originality. Comparing the results of mechanical and metallographic studies, it can be argued that the desired properties of Al-Cu-Mg samples appear after dispersion hardening, which confirms the optimal hardening conditions. The results of the photogrammetric evaluation of samples in the micro range demonstrate the flexibility and accuracy potential of photogrammetric measurement methods and their subsequent processing, interpretation, and integration with EDX analysis to select optimal study sites.
Practical value. An integrated approach to the analysis of materials using the SEM stereomicrophotogrammetric method, mechanical and metallographic studies, and EDX analysis was tested in this work.
Keywords: Al-Cu-Mg alloy, SEM stereo microphotogrammetry, mechanical studies, metallographic studies, EDX analysis
References.
1. Bhat, B. N. (2018). Aerospace materials and Applications. American Institute of Aeronautics and Astronautics, Inc.
2. Chen, J., Ling, K., Deng, P., Mo, W., Tang, C., Ouyang, Z., Luo, B., & Bai, Z. (2023). Effect of Mg content on microstructure, mechanical properties and intergranular corrosion properties of Al-Cu-Mg-Ag alloys. Materials Today Communications, 34, 105363. https://doi.org/10.1016/j.mtcomm.2023.105363.
3. DIN EN 573-3:2019+A1:2022 – Aluminium and aluminium alloys – Chemical composition and form of wrought products – Part 3: Chemical composition and form of products (2022).
4. Hemmleb, M. (2002). Photogrammetrische Auswertung elektronenmikroskopischer Bilddaten. https://doi.org/10.14279/depositonce-321.
5. Ivanov, R., Deschamps, A., & De Geuser, F. (2018a). Clustering kinetics during natural ageing of Al-Cu based alloys with (Mg, Li) additions. Acta Materialia, 157, 186-195. https://doi.org/10.1016/j.actamat.2018.07.035.
6. Ivanov, R., Deschamps, A., & De Geuser, F. (2018b). High throughput evaluation of the effect of Mg concentration on natural ageing of Al-Cu-Li-(Mg) alloys. Scripta Materialia, 150, 156-159. https://doi.org/10.1016/j.scriptamat.2018.03.024.
7. Klobes, B., Maier, K., & Staab, T. E. M. (2011). Natural ageing of Al-Cu-Mg revisited from a local perspective. Materials Science and Engineering: A, 528(7), 3253-3260. https://doi.org/10.1016/j.msea.2011.01.002.
8. Kolednik, O. (1981). Ein Beitrag zur Stereophotogrammetrie am Rasterelektronenmikroskop. Praktische Metallographie, 18, 562-573.
9. Kovarik, L., & Mills, M. J. (2012). Ab initio analysis of Guinier–Preston–Bagaryatsky zone nucleation in Al–Cu–Mg alloys. Acta Materialia, 60(9), 3861-3872. https://doi.org/10.1016/j.actamat.2012.03.044.
10. Luhmann, T. (2010). Nahbereichsphotogrammetrie – Grundlagen, Methoden, Anwendungen.
11. Metals handbook. Volume 12: Fractography (n.d.). Retrieved from https://www.osti.gov/biblio/6512607.
12. Motro, P. F. K., Kursoglu, P., & Kazazoglu, E. (2012). Effects of different surface treatments on stainability of ceramics. The Journal of Prosthetic Dentistry, 108(4), 231-237. https://doi.org/10.1016/S0022-3913(12)60168-1.
13. Patel, V., Li, W., Vairis, A., & Badheka, V. (2019). Recent development in friction stir processing as a solid-state grain refinement technique: microstructural evolution and property enhancement. Critical Reviews in Solid State and Materials Sciences, 44(5), 378-426.
14. Piazzesi, R., Berrilli, F., Del Moro, D., & Egidi, A. (2012). Algorithm for real time flare detection. Memorie della Societa Astronomica Italiana Supplementi, 19, 109.
15. Schmid, M., Liebel, A., Moldovan, G., Lackner, R., Steigenhöfer, D., Niculae, A., & Soltau, H. (2018). New Possibilities for State-of-the-Art Electron Microscopy with Fast Backscattered Electron Detectors. Microscopy and Microanalysis, 24(S1), 650-651.
16. Solís Moreno, C., Sanz-Moliner, J. D., Pascual La Rocca, A., Nart, J., & Santos Alemany, A. (2013). In vitro evaluation of the root surface microtopography following the use of two polishing systems by Confocal Microscopy (CFM) and Scanning Electron Microscope (SEM). Oral Health and Dental Management, 12(4), 243-247.
17. Uhl, A., Melnyk, Y., Melnyk, O., Boyarska, I., & Melnychuk, M. (2020). Application of Microphotogrammetric and Material Science Techniques in the Study of Materials on the Example of Alloy AlZnMgCu. In В V. Ivanov, J. Trojanowska, J. Machado, O. Liaposhchenko, J. Zajac, I. Pavlenko, M. Edl, & D. Perakovic (Eds.). Advances in Design, Simulation and Manufacturing II, (pp 477-486). Springer International Publishing.
18. Uhl, A. V., Melnyk, O. V., Melnyk, Y. A., & Ilyin, L. V. (2021). Microphotogrammetric approach in the study of alsimg alloys. Metallofizika i Noveishie Tekhnologii, 43(2). https://doi.org/10.15407/mfint.43.02.0255.
19. Yang, Z., Erdle, I., Liu, C., & Banhart, J. (2022). Clustering and precipitation in Al-Mg-Si alloys during linear heating. Journal of Materials Science & Technology, 120, 78-88. https://doi.org/10.1016/j.jmst.2021.11.062.
Newer news items:
- Utilization of the secondary resources of titanium-zirconium pits when constructing highways - 28/08/2023 20:15
- The role of the formation of the environmental management system in the improvement of international economic relations - 28/08/2023 20:15
- Improving a process of managing dynamic occupational risks - 28/08/2023 20:15
- Soil contamination status using contamination indicators and the health risk - 28/08/2023 20:15
- Parameterization of the statistical model for electrical energy efficiency control - 28/08/2023 20:15
- Energy transition: the future of energy on the base of smart specialization - 28/08/2023 20:15
- Designing the working surfaces of rotary planetary mechanisms - 28/08/2023 20:15
- Improvement of the service life of mining and industrial equipment by using friction modifiers - 28/08/2023 20:15
- Hydrodynamics of vapor-liquid flows in curvilined channels of separation devices of power plants - 28/08/2023 20:15
- Substantiating a method for computer analysis of the stress-strain state of the tubbing erector manipulator mechanism - 28/08/2023 20:15
Older news items:
- Magnetic stimulation of chemical reactions in coal - 28/08/2023 20:15
- Selection and justification of drilling and blasting parameters using genetic algorithms - 28/08/2023 20:15
- Improving the technology of extracting coal concentrate from fly ash from thermal power plants - 28/08/2023 20:15
- A new mining method for reopening the opencast mine of Kef Essennoun - 28/08/2023 20:15
- Tectonics and gravity field structure of Central Kazakhstan - 28/08/2023 20:15
- Mining and geological models of virtual complex ore blocks of the bench - 28/08/2023 20:15
- Predicting zones of increased water inflows in local folded structures - 28/08/2023 20:15