Minimization of dynamic changes in the tension of long products behind the outlet cage in rolling stock production in coils

User Rating:  / 0
PoorBest 

Authors:


O.Boyko*, orcid.org/0000-0002-9714-2843, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

V.Kuvaiev, orcid.org/0000-0001-6329-071X, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

D.Beshta, orcid.org/0000-0003-2848-2737, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

O.Potap, orcid.org/0000-0001-8643-0228, Ukrainian State University of Science and Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

S.Matsiuk, orcid.org/0000-0001-6798-5500, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

* Corresponding author e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.


повний текст / full article



Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2022, (6): 076 - 083

https://doi.org/10.33271/nvngu/2022-6/076



Abstract:



Purpose.
Justification of technical solutions as to the reduction of the amplitude and reduction of the dynamic change duration in the tension of the rolling stock at the exit of the output cage when moving to winding a new layer to an acceptable level in terms of its effect on the resulting profile of the rolled product through the control of the rotation frequency of an output cage.


Methodology.
The conducted research was based on a complex model of the process of rolled steel winding with a Garrett-type winder and the tension of rolled steel in the area of the exit cage-winder. To control the actual amount of tension at the output cage exit, it is suggested to use the amount of free deflection of the rolled steel directly behind the cage. The research was carried out by simulating the process of rolled steel winding according to the basic control scheme and control schemes that predict the influence on both drives, i.e. the winder drive and the output cage drive according to the actual value of tension, in various combinations with further analysis and comparison of the obtained results.


Findings.
It was established that the correction for the deviation of the actual rolling tension in the finishing cage-winder area from the specified value of the winding current of the winder electric drive does not eliminate rolling tension when switching to the next layer winding and the oscillating form of the transition process, which are characteristic of the basic rolling winding scheme. In turn, the correction of the rotation frequency of the output cage rolls drive reduces the amplitude of the roll tension jerk by almost half with a simultaneous reduction in the time of the transition process and readjustment when switching to a new layer winding.


Originality.
It has been shown for the first time that the introduction of the roll tension control circuit by correcting the high-speed rolling mode of the output cage ensures minimization of dynamic changes in the rolled steel tension when switching to a new layer winding and reduces the probability of local tightening of rolled steel profile.


Practical value.
The use of the described technical solutions in the control system of the section of rolled products winding of the small-grade wire mill DSDS 250/150-6 PJSC ArcelorMittal Kryvyi Rih ensures the improvement of the commercial properties of the winding of rolled products produced on the rolling mill.



Keywords:
winder, rolling tension, control of the winding current, control of the rolling speed mode

References.


1. Cimolino, M., Fabbro, C., & Taurino, A. (2014). Latest improvements in quality and process control of new bar-in-coil lines. MPT Metallurgical Plant and Technology International, 3(4), 52-61. Retrieved from https://goo.su/74zU.

2.Fabbro, C. (2016). 20 Euro/T savings by combining EWR and spooler technologies optimizing bar mill yield for the lowest OPEX. AISTech Iron and Steel Technology Conference Proceedings, 2307-2313. Retrieved from https://goo.su/QW3F.

3.Castenetto, M., Taurino, A., & Mestroni, A. (2015). EWR endless welding rolling system and spooler line. Results and combined application for endless rolling of spooled coils. SEAISI Quarterly (South East Asia Iron and Steel Institute), 44.3, 25-29. Retrieved from https://goo.su/BOPUCNU.

4.Fabbro, C., Durisotti, M., & Simecek, P. (2016). DLPP Quality management software tool for rolling and heat treatment optimization. TMP 5th International Conference on ThermoMechanical Processing. Retrieved from https://goo.su/nU3UL.

5. Kuvaiev, V.M., & Beshta, D.. (2017). Dynamic model of interaction of mechanisms on the section between the roll mill stand and the coiler in the process of wire winding by garrett reel. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (4), 61-66.

6.Cimolino, M., Fabbro, C., & Taurino, A. (2015). The latest achievements in the field improving product quality and technological control in small-section finishing areas profiles in riots. Metallurgical production and technology, 1, 20-32.

7. Nekipelov, V.S., & Shikin, A.V. (2019). Coiling process design basics and pilot testing of innovative coiling processes. Mechanical equipment of metallurgical plants, 1, 4-14.

8. Berdnyk, M. (2019). Mathematic model and method for solving the heat-exchange problem in electron-beam welding of arbitrary areas. Solid State Phenomena, 291, 173-182. https://doi.org/10.4028/www.scientific.net/SSP.291.173.

9. Berdnyk, M. (2018). The mathematic model and method for solving the dirichlet heat- exchange problem for empty isotropic rotary body. Solid State Phenomena, 277, 168-177. https://doi.org/10.4028/www.scientific.net/SSP.277.168.

10. Starostenko, O., Trygub, I.G., Cruz-Perez, C., Alarcon-Aquino,V., & Potap, O.E. (2017). Visual Remote Monitoring and Control System for Rod Braking on Hot Rolling Mills. Mexican Conference on Pattern Recognition, 297-307. Retrieved from https://goo.su/T7DDo.

 

Visitors

5032270
Today
This Month
All days
6
3690
5032270

Guest Book

If you have questions, comments or suggestions, you can write them in our "Guest Book"

Registration data

ISSN (print) 2071-2227,
ISSN (online) 2223-2362.
Journal was registered by Ministry of Justice of Ukraine.
Registration number КВ No.17742-6592PR dated April 27, 2011.

Contacts

D.Yavornytskyi ave.,19, pavilion 3, room 24-а, Dnipro, 49005
Tel.: +38 (056) 746 32 79.
e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
You are here: Home About the journal contact EngCat Archive 2022 Content №6 2022 Minimization of dynamic changes in the tension of long products behind the outlet cage in rolling stock production in coils