Simplified plugging material

User Rating:  / 0
PoorBest 

Authors:

V. M. Orlovskyy, Cand. Sc. (Tech.), orcid.org/0000-0002-8749-5354, O. M. Beketov National University of Urban Economy in Kharkiv, Kharkiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

V. М. Savyk, Cand. Sc. (Tech.), orcid.org/0000-0002-0706-0589, Poltava National Technical Yuri Kondratyuk University, Poltava, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.; This email address is being protected from spambots. You need JavaScript enabled to view it.; This email address is being protected from spambots. You need JavaScript enabled to view it.

P.  О. Molchanov, Cand. Sc. (Tech.), orcid.org/0000-0001-5335-4281, Poltava National Technical Yuri Kondratyuk University, Poltava, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.; This email address is being protected from spambots. You need JavaScript enabled to view it.; This email address is being protected from spambots. You need JavaScript enabled to view it.

A. M. Pokhylko, orcid.org/0000-0003-4565-3411, Poltava National Technical Yuri Kondratyuk University, Poltava, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.; This email address is being protected from spambots. You need JavaScript enabled to view it.; This email address is being protected from spambots. You need JavaScript enabled to view it.

Abstract:

Purpose. Toreceiveplugging material of lower density based on the mixture of viscous (Portland cement PCTI-100, PCTI-50) and relieving additive. To realize it, we used expanded perlitesand as relieving additive for viscous material. To prove that plugging material based on standard plugging Portland cement and expanded perlite sand has high technological properties and corresponds with current standards.

Methodology. The research was performed with the usage of theoretical and experimental methods. Experimental studies were carried out using laboratorial equipment that models the pressure and the temperature of productive layer. Measuring the technological characteristics of plugging solution and formed stone was accomplished with the usage of standard registering equipment. The density of plugging mixture was scaled with the pycnometer, water and mixture ratio of solutions was chosen with the usage of the dehiscence cone DC-1; water separation of plugging material was measured according to the standard methodology (DSTU BV.2.7-86-99 being still legal), the time of setting time of plugging solution was defined with the consistometer KS-3, for researching of adhesion there was used the laboratorial press PSU-10 with hydraulic drive and special console, defining the extreme parameters of stone tightness while bending was carried on according to DSTU BV.2.7-86-99 on special equipment for testing the line objects to stretch while bending and pressing using the press PSU-10. The number of carried out experiments is enough to obtain results with confiding probability of 0.95.

Findings. Relieving mixture based on plugging Portland cement PCTI-100 (PCTI-50) with the relieving additive was developed and studied. The minimal density of plugging solution based on offered material is 1160–1190 kg/m3 while following other characteristics of plugging solution and stone according to the legal standards.

Originality. Effective recipes of plugging solution of lower density based on standard plugging Portland cement and relieving additive – expanded perlitesand – were developed and chosen.

Practical value. Development of the recipes of plugging solutions is perspective while cementing the wells, which have been drilled for oil and gas, especially in complicated mining and geological conditions of geological-prospecting areas and exploiting the hydrocarbon deposits. “Recommendations as for the usage of easy (simplified) plugging materials for wells cementing” were formulated, which have been accepted to use in the system of the State geological service of Ukraine.

References.

1. Agzamov, F. A., Izmukhambetov, B. S. and Tokunova, E. A., 2011. Drilling mud and cement chemistry. Moscow: Nedra.

2. Hesham Alsharie, Talal Masoud, Aziz Ibrahim Abdulla and Aseel Ghanemт, 2015. Properties of Lightweight Cement Mortar Containing Treated Pumice and Limestone. Journal of Engineering and Applied Sciences, 10(5), pp. 96–101. DOI: 10.3923/jeasci.2015.96.101.

3. Balthar, V. K. C. B. L. M., Toledo Filho, R. D., E. de MoraesRego Fairbairn and C. R. de Miranda, 2016. Durability of Lightweight Slurries for Oilwell Cementing.Key Engineering Materials. Switzerland. – Trans Tech Publications [online], 711, рp. 203–210. Available at: <https://www.scientific.net/KEM.711.203> [Accessed 9 August 2017].

4. Bubnov, A. S., Khorev, V. S. and Boyko, I. A., 2015. The effect of lightweight agents on the density of cement slurry applied during oil and gas well drilling. Scientific and Technical Challenges in the Well Drilling Progress IOP Publishing IOP Conf. Series: Earth and Environmental Science, 24(2015)012008. DOI:10.1088/1755-1315/ 24/1/012008.

5. Concern Cement, 1999. Oil-well Portland cement DSTU BV.2.7-88-99. 1999/Derzhstandart Ukrainy/ – Kiev (now active) [pdf]. Available at: <http://ksv.do.am/GOST/DSTY_ALL/DSYU1/dstu_b_v.2.7-88-99.pdf> [Accessed 14 August 2017].

6. GOST 10832-91. Sand and road metal perlite expanded [Effective since 1 January 1992]. / Specifications (now active) [online]. Available at: <http://www.vost.ru/docs/gost/10832-91http://ksv.do.am/GOST/DSTY_ALL/DSYU1/dstu_b_v.2.7-88-99.pdf> [Accessed 22 September 2017].

7. Orlovskyi, V. M., Pokhylko, A. M. and Krytskyi, V. V., 2016. New lightweight plugging materials. Zbirnyk naukovykh prats UkrDHRI, 4, рp. 107–114.

8. Orlovskyi, V. M., Mykhailenko, S. H. and Luzhanytsia, O. V, 2012. The lightweight plugging materials. Ukraine. Pat. 73377. No. u 2012 01875; Declared on February 20, 12; Opubl. 25.09.12, Bul. No. 18.

9. Borzenko, E. Y. and Khehai, E. Y., 2016. The computational simulation of Balkli–Gershelya liquid stationary flow on the sharp growing supply tube. Vestnik Tomskogo Gosudarstvennogo Universiteta. Matematika i Mehanika, 1(39), рp 68–81. DOI: https://doi.org/ 10.17223/19988621/39/8.

10. Lyakh, M. M., Savyk, V. М. and Molchanov, P. О., 2017. Experimental and industrial research pinogenerating devices. Rozrobka korysnyh kopalyn. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, 5(161), pp. 17–23.

11. Biletskyi, V.  S., Shendrik, T. and Sergeev, P., 2012. Derivatography as the method of water structure studying on solid mineral surface. In: Geomechanical Processes During Underground Mining. London: CRC Press Taylor & Francis Group [online], pр. 181‒184. Available at: <http://www.crcnetbase.com/doi/abs/10.1201/b13157-31> [Accessed 12 October 2017].

 повний текст / full article



Visitors

6227600
Today
This Month
All days
1432
54277
6227600

Guest Book

If you have questions, comments or suggestions, you can write them in our "Guest Book"

Registration data

ISSN (print) 2071-2227,
ISSN (online) 2223-2362.
Journal was registered by Ministry of Justice of Ukraine.
Registration number КВ No.17742-6592PR dated April 27, 2011.

Contacts

D.Yavornytskyi ave.,19, pavilion 3, room 24-а, Dnipro, 49005
Tel.: +38 (056) 746 32 79.
e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.