Articles

Cable line equivalent circuit parameters determination using the instantaneous power components

• 
• 

User Rating:  / 0

PoorBest 

Details

Category: Content №2 2024

Last Updated on 01 May 2024

Published on 30 November -0001

Hits: 2754

Authors:

O.Bialobrzheskyi*, orcid.org/0000-0003-1669-4580, Kremenchuk Mykhailo Ostrohradskyi National University, Kremenchuk, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

O.Todorov, orcid.org/0000-0001-5703-6790, Kremenchuk Mykhailo Ostrohradskyi National University, Kremenchuk, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

A.Postil, orcid.org/0000-0001-9411-7047, Kremenchuk Mykhailo Ostrohradskyi National University, Kremenchuk, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

M.Bezzub, orcid.org/0000-0002-5595-4464, Kremenchuk Mykhailo Ostrohradskyi National University, Kremenchuk, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

A.Sulym, orcid.org/0000-0001-8144-8971, State Enterprise “Ukrainian Scientific Railway Car Building Research Institute”, Kremenchuk, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

* Corresponding author e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

повний текст / full article

Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2024, (2): 096 - 103

https://doi.org/10.33271/nvngu/2024-2/096

Abstract:

Purpose. Development of a method for determining the cable line substitution scheme parameters based on the components of its instantaneous power.

Methodology. Determination of unknown parameters of the cable line mode using the harmonic balance method. Determination of the U-shaped substitution scheme elements parameters is performed using power harmonics and their balance at the corresponding frequencies. For frequency-dependent elements, it is taken into account that the same power harmonic can be formed by different current and voltage harmonics.

Findings. A method for determining the parameters of the cable line substitution scheme using the power components of its elements is proposed, which is distinguished by the fact that the total number of system equations for determining the parameters can be increased due to the use of power. The study of the proposed method for determining the cable line substitution scheme parameters based on the power components, based on the model compiled in the visual programming package, allowed us to establish that the largest parameter determination error is characteristic of active conduction.

Originality. With the instantaneous power determination of the cable line substitution scheme reactive elements, it was found that during the calculation of the instantaneous power there is a peculiarity of taking into account the voltage harmonic number depending on the combination of harmonic numbers.

Practical value. The proposed method can be developed on the sectioning of the U-shaped line substitution scheme to determine the change in the cable line substitution scheme parameters during its operation without disconnecting the line, unlike existing methods.

Keywords: cable line, power, voltage, harmonics, orthogonal components, harmonic frequency

References.

1. Ngwenyama, M. K., Le Roux, P. F., & Ngoma, L. J. (2021). Traveling Wave Fault Location Detection Technique for High Voltage Transmission Lines. 2 ^nd International Conference for Emerging Technology (INCET), (pp. 1-7). Belagavi, India. https://doi.org/10.1109/INCET51464.2021.9456334.

2. Lan, X., Zhou, N., Liu, M., Sun, T., Wang, J., & Wang, Q. (2021). Identification of defects in HV cable sheath based on equivalent impedance spectrum characteristic coding. International Journal of Electrical Power & Energy Systems, (130), 130-139. https://doi.org/10.1016/j.ijepes.2021.107008.

3. Wang, H., Liu, T., Peng, X., Zhou, H., & Shi, X. (2019). Leakage Currents Separation of Cross-bonded Cables Based on Sheath Current Vector Difference. IEEE PES Asia-Pacific Power and Energy Engineering Conference (APPEEC), (pp. 1-4). Macao, China. https://doi.org/10.1109/APPEEC45492.2019.8994452.

4. Ghosh, R., Seri, P., & Montanari, G. (2021). Partial discharge measurements and life estimation in DC electrical insulation during voltage transients and steady state. Electric Power Systems Research, (194), 184-194. https://doi.org/10.1016/j.epsr.2021.107117.

5. Marzinotto, M., & Mazzanti, G. (2015). The statistical enlargement law for HVDC cable lines part 1: theory and application to the enlargement in length. IEEE Transactions on Dielectrics and Electrical Insulation, (pp. 192-201). https://doi.org/10.1109/TDEI.2014.004626.

6. Yang, Y., Hepburn, D., Zhou, C., Jiang, W., Yang, B., & Zhou, W. (2015). On-line monitoring and trending of dielectric loss in a cross-bonded HV cable system. IEEE 11^th International Conference on the Properties and Applications of Dielectric Materials (ICPADM), (pp. 301-304). Sydney, Australia. https://doi.org/10.1109/ICPADM.2015.7295268.

7. Luo, J., Zhang, K., Chen, T., Zhao, G., Wang, P., & Feng, S. (2011). Distributed parameter circuit model for transmission line. International Conference on Advanced Power System Automation and Protection, (pp. 1529-1534). Beijing, China. https://doi.org/10.1109/APAP.2011.6180607.

8. Ma, S., Guo, J., Sun, H., & Yu, Y. (2011). The comparison and analysis of lumped parameter equivalent circuits of transmission line. International Conference on Advanced Power System Automation and Protection, (pp. 1225-1229). Beijing, China. https://doi.org/10.1109/apap.2011.6180565.

9. Zhang, Y., Li, B., Jiang, X., & Li, Z. (2015). A fault location method for extra-high voltage mixed line based on variation of sequence voltage. 5 ^th International Conference on Electric Utility Deregulation and Restructuring and Power Technologies (DRPT), (pp. 916-921). Changsha, China. https://doi.org/10.1109/drpt.2015.7432358.

10. Ding, L., Bi, T., & Zhang, D. (2011). Transmission line parameters identification based on moving-window TLS and PMU data. International Conference on Advanced Power System Automation and Protection, (pp. 2187-2191). Beijing, China. https://doi.org/10.1109/APAP.2011.6180790.

11. Dasgupta, K., & Soman, S. A. (2013). Line parameter estimation using phasor measurements by the total least squares approach. IEEE Power & Energy Society General Meeting, (pp. 1-5). Vancouver, BC, Canada. https://doi.org/10.1109/PESMG.2013.6672179.

12. Zhou, Y., Xu, G., & Chen, Y. (2016). Fault Location in Power Electrical Traction Line System. Energies 2012, (5), 5002-5018. https://doi.org/10.3390/en5125002.

13. Hoshmeh, A. (2016). A three-phase cable model based on lumped parameters for transient calculations in the time domain. IEEE Innovative Smart Grid Technologies – Asia (ISGT-Asia), (pp. 580-585). Melbourn, Australia. https://doi.org/10.1109/ISGT-Asia.2016.7796449.

14. Chrysochos, A. I., Papadopoulos, T. A., & Papagiannis, G. K. (2014). Robust Calculation of Frequency-Dependent Transmission-Line Transformation Matrices Using the Levenberg–Marquardt Method. IEEE Transactions on Power Delivery, 29(4), 1621-1629. https://doi.org/10.1109/TPWRD.2013.2284504.

15. Kovalchuk, V., Korenkova, T., Rodkin, D., Kravets, O., & Qawa­qzeh, M. Z. (2021). Power Method of the Electrohydraulic Complex Parameter Identification Based on the Physical Model. IEEE International Conference on Modern Electrical and Energy Systems (MEES), (pp. 1-6). Kremenchuk, Ukraine. https://doi.org/10.1109/MEES52427.2021.9598775.

16. Zagirnyak, M., Rodkin, D., & Romashykhin, I. (2017). The possibilities of Tellegen’s theorem in the identification electrotechnical problems. International Conference on Modern Electrical and Energy Systems (MEES), (pp. 152-155). Kremenchuk, Ukraine. https://doi.org/10.1109/MEES.2017.8248875.

17. Bialobrzheskyi, O. V., RodKin, D., & Gladyr, A. (2022). Electrical power components decomposition of periodic polyharmonic current. COMPEL – The international journal for computation and mathematics in electrical and electronic engineering, (4), 1134-1145. https://doi.org/10.1108/COMPEL-10-2021-0397.

18. Bezzub, M., Bialobrzheskyi, O., Todorov, O., Kurliak, P., & Reva, I. (2021). Current Harmonics Distribution Influence of a Traction Transformer Secondary Winding on a Power Losses Level Taking Into Account Distortion Power. IEEE International Conference on Modern Electrical and Energy Systems (MEES), (pp. 1-6). Kremenchuk, Ukraine. https://doi.org/10.1109/MEES52427.2021.9598623.

19. Bialobrzheskyi, O. V., & Rod’Kin, D. (2022). A positive, negative and zero sequences electric power, to improve upon the standard IEEE 1459-2010. COMPEL – The international journal for computation and mathematics in electrical and electronic engineering, 42(2), 402-424. https://doi.org/10.1108/COMPEL-03-2022-0109.

20. Qawaqzeh, M. Z., Bialobrzheskyi, O., & Zagirnyak, M. (2019). Identification of distribution features of the instantaneous power components of the electric energy of the circuit with polyharmonic current. Eastern-European Journal of Enterprise Technologies, 2(8-98), 6-13. https://doi.org/10.15587/1729-4061.2019.160513.

• < Prev
• Next >