Articles

Analytical and experimental assessment of screw centrifugal pump at improving its design

User Rating:  / 0
PoorBest 

Authors:


H.Nazarenko, orcid.org/0000-0001-7304-7246, Yuzhnoye State Design Office, Dnipro Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.


повний текст / full article



Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2021, (4): 063 - 068

https://doi.org/10.33271/nvngu/2021-4/063



Abstract:



Purpose. Development of analytical and experimental assessment of screw centrifugal type pump at a design stage, which permits defining more precisely its power and cavitation characteristics.


Methodology. To achieve the above-mentioned purpose, the technique that includes the following possibilities was developed: make the list of changes which increase the efficiency of the existing pump; quickly and with high precision to estimate influence of certain constructive and/or regime changes on efficiency of the existing pump without difficult flow calculations; determine the need to develop a new pump, if all the changes of the existing pump did not give a positive result; determine changes influence on cavitation properties of the existing pump; calculate the efficiency dispersion during hydraulic tests of the modified pump.


Findings. During the research, an analytical and experimental technique which permits determining increase in the pump efficiency quickly and with high precision at the change in pump design and/or operating mode was developed. The developed technique determines how all changes in the existing pump influence its anti-cavitation properties. The above mentioned technique also allows calculating the efficiency dispersion during hydraulic tests of the modified pump. The technique determines the need to develop a new pump, if all the changes in the existing pump did not give a positive result. The use of the presented calculation technique, at a design stage, allows estimating the efficiency of the developed pump more precisely. The developed technique allows increasing the efficiency assessment accuracy and cavitation characteristics of low-flow high-speed screw centrifugal pump.


Originality. During the research, new empirical dependences were obtained that permit defining more precisely power and cavitation characteristics of low-flow high-speed screw centrifugal pump.


Practical value. The presented technique at a design stage allows estimating the developed pump efficiency more precisely. Due to this, it is possible to reduce the time for pump development and its development tests.



Keywords: pump efficiency, cavitation speed coefficient, low-flow high-speed pump

References.

1. Mueller, T. J., Pinera, A., Brooks, S.M., Appleby, J.W., & Leonard, T.G. (2017). Turbopump with a single piece housing and a smooth enamel glass surface. (USA Patent No. US20190032604A1 USA F02K9/46).

2. Borodin, G.К., Petrov, A.I., & Protopopov, А.А. (2016). The technique and the algorithm of the determination of the main design parameters of the low mass centrifugal pump. Мoscow. https://doi.org/10.20948/prepr-2016-63.

3. Beshta, O.S., Fedoreiko, V.S., Palchyk, A.O., & Burega, N.V. (2015). Autonomous power supply of the objects based on biosolid oxide fuel systems. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (2), 67-73.

4. Grigorev, S.V., Savin, R.М., & Shahanov, L.A. (2015). Possibility of improvementvenergy performance of centrifugal pumps. Izvestiya TulGU, (7, part 2), 122-127.

5. Kretinin, А.V., Ivanov, А.V., & Galdin, D.N. (2016). Calculation comparison of variants for profiling centrifugal pump impeller. The Bulletin of Voronezh State Technical University, 12(4), 26-31.

6. Volkov, A.V., Parugin, А.G., Davudov, А.I., & Hovanov, G.P. (2011). Improving the energy efficiency of a centrifugal pump by using a variable pitch vane system. Safety and Reliability of Power Industry, (3), 53-56.

7. Lomakin, V.О., Petrov, А.I., & Kuleshova, М.S. (2014). Investigation of two-phase flow in axial-centrifugal impeller by hydrodynamic modeling methods. Science & Education of the Bauman MSTU, (9), 37-54.

8. Zubanov, V.M., & Shabliy, L.S. (2014). FD-modeling of processes in a high-pressure oxidizer pump for the turbopump assembly of a liquid rocket engine. Vestnik of the Samara State Aerospace University, (5(47), part 1), 148-153.

9. Ivanov, Е.А., Kaleev, V.А., & Shumilin, S.А. (2018). Modernization of the flow section of the main circulation pump GCN 22600-87. Izvestiya vuzov. Problemy energetiki, 20(7-8), 63-70.

10. Bylugin, U.А., Ivanov, А.V., & Galdin, D.N. (2017). Creating a parametric optimization mathematical model of pump impeller with help of ANSYS Workbench. The Bulletin of Voronezh State Technical University, 13(2), 29-32.

11. Sulinov, A.V., Shabliy, L.S., & Zubanov, V.M. (2015). Methods of modeling the work process of hydrogen screw-centrifugal pumps using ANSYS CFD. Vestnik of the Samara State Aerospace University, 14(3, part 2), 305-315. https://doi.org/10.18287/2412-7329-2015-14-3-305-315.

12. Beshta, O., Kuvaiev, V., Mladetskyi, I., & Kuvaiev, M. (2020). Ulpa particle separation model in a spiral classifier. Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu, (1), 31-35. https://doi.org/10.33271/nvngu/2020-1/031. 

 

Visitors

6226947
Today
This Month
All days
779
53624
6226947

Guest Book

If you have questions, comments or suggestions, you can write them in our "Guest Book"

Registration data

ISSN (print) 2071-2227,
ISSN (online) 2223-2362.
Journal was registered by Ministry of Justice of Ukraine.
Registration number КВ No.17742-6592PR dated April 27, 2011.

Contacts

D.Yavornytskyi ave.,19, pavilion 3, room 24-а, Dnipro, 49005
Tel.: +38 (056) 746 32 79.
e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
You are here: Home