Науковий вісник НГУ

Testing the fragmentation of railway ballast material by laboratory methods using Proctor compactor

• 
• 

User Rating:  / 0

PoorBest 

Details

Category: Content №1 2024

Last Updated on 29 February 2024

Published on 30 November -0001

Hits: 2183

Authors:

E.Huschek-Juhász, orcid.org/0000-0002-5544-3146, Széchenyi István University, Győr, Hungary

A.Németh, orcid.org/0000-0002-3477-6902, Széchenyi István University, Győr, Hungary

M.Sysyn, orcid.org/0000-0001-6893-0018, Institute of Railway Systems and Public Transport, TU Dresden, Dresden, the Federal Republic of Germany

G.Baranyai, orcid.org/0000-0003-3369-8823, Széchenyi István University, Győr, Hungary

J.Liu, orcid.org/0000-0002-4779-7761, China Railway First Group Xinyun Engineering Co., Ltd, Xi’an, the People’s Republic of China

S.Fischer*, orcid.org/0000-0001-7298-9960, Széchenyi István University, Győr, Hungary

* Corresponding author e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

повний текст / full article

Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu. 2024, (1): 058 - 068

https://doi.org/10.33271/nvngu/2024-1/058

Abstract:

The physical classification of crushed stone and gravel used in railway construction is based on their strength and endurance and is performed by a laboratory test method using a rotating drum or a mortar method. The values of fracture resistance calculated using the Los Angeles method and abrasion calculated using the Micro-Deval method show a corresponding correlation and require further investigation.

Purpose. The development of a new method for measuring rock material fracture that is consistent with widely used standards while also being more comparable to real-world railway operating conditions. Certainly, both standard tests are essential for ensuring product homogeneity during production, so the new recommended method is only a supplement.

Methodology. The Proctor device was used to induce so-called shock loads from above, similar to railway loading conditions. Unlike the standard method, the andesite material was placed in a standard cylinder in these tests. The samples were pre-screened and sorted; the specified weight was approximately 1,300 g, and the specified sizes of the individual particles were 6.3, 8.0 and 11.2 mm. Only prewashed and dried materials of NZ (fine crushed stone) or KZ (special crushed stone) from four different quarries (Tállya, Szob, Nógrádkövesd, Recsk) with different rock physics characteristics were considered. The Proctor compactor machine was used because of its calculable labor (19.86 J/impact) and the crushing effect of the calculable impacts (64, 128, 256 and 1,028 blows). Even after loading different numbers of impacts, homogeneous samples from different quarries were sieved to measure the masses of fragments per fraction.

Findings. The set of measurements made it possible to establish a series of fragmentation and degradation curves for each of the three repeated measurements based on the composition of the material and the number of blows, which showed the degradation of samples with different physical and mechanical properties of the rock material and particle sizes. With an increasing number of impacts, the amount of crushed material in the sample increased, but the distribution of crushed material did not decrease evenly and proportionally as the number of impacts increased. Parameters and indices were also computed to identify various correlations (i. e., F_V, d < 22.4, d < 0.5, d < 0.063 mm, C_U, M ratio,  ratio). Some of them (e. g., F_V) needed to be changed, but they were predefined due to the nature of the tests.

Originality. While many standard and alternative railway track ballast fragmentation test methods and measurement tools are available, this paper proposes a new laboratory method and demonstrates the specific measurement and application effectiveness.

Practical value. In addition to standard tests that are already widely used, the new method for measuring the fractional composition of railway ballast can help simulate real-world operating conditions of a railroad track in the laboratory. This method will improve the safety of railway operations.

Keywords: railway track, ballasted track, material fractions, laboratory test, Proctor device

References.

1. Horvát, F. (2015). Mérnöki módszerek III. Széchenyi István University. Győr.

2. Internet law library (2023, October 31). Retrieved from https://net.jogtar.hu/jogszabaly?docid=a1300275.kor.

3. European Committee for Standardization (2012). Aggregates for railway ballast (EN 13450). Retrieved from https://standards.iteh.ai/catalog/standards/cen/c05b9399-6075-42e0-9274-28742fa20327/en-13450-2013.

4. European Committee for Standardization (2012). Tests for mechanical and physical properties of aggregates – Part 1: Determination of the resistance to wear (micro-Deval) (EN 1097-1). Retrieved from https://standards.iteh.ai/catalog/standards/cen/0704a937-7494-49be-827a-1da432fc0024/en-1097-1-2011.

5. European Committee for Standardization (2020). Tests for mechanical and physical properties of aggregates – Part 2: Methods for the determination of resistance to fragmentation (EN 1097-2). Retrieved from https://standards.iteh.ai/catalog/standards/cen/2b59008c-ab4d-428f-9e85-780705498a57/en-1097-2-2020.

6. Kurhan, M. B., Kurhan, D. M., Husak, M. A., & Hmelevska, N. (2022). Increasing the efficiency of the railway operation in the specialization of directions for freight and passenger transportation. Acta Polytechnica Hungarica, 19(3), 231-244. https://doi.org/10.12700/APH.19.3.2022.3.18.

7. Gáspár, L., Horvát, F., & Lublóy, L. (2011). Lifetime of transport infrastructure facilities. Universitas-Győr Nonprofit Kft., Győr.

8. Czinder, B., Vásárhelyi, B., & Török, Á. (2021). Long-term abrasion of rocks assessed by micro-Deval tests and estimation of the abrasion process of rock types based on strength parameters. Engineering Geology, 282, 105996. https://doi.org/10.1016/j.enggeo.2021.105996.

9. Shehu, S. A., Yusuf, K. O., Zabidi, H., Jimoh, O. A., & Ha­shim, M. H. M. (2023). Blasting efficiency in granite aggregate quarry based on the combined effects of fragmentation and weighted environmental hazards. Mining of Mineral Deposits, 17(1), 120-128. https://doi.org/10.33271/mining17.01.120.

10. Haddad, J., Alfaqs, F., Al-quraan, T., & Ikhries, I. I. (2023). Investigation of vibrating jaw crusher experimental variables. Mining of Mineral Deposits, 17(3), 49-55. https://doi.org/10.33271/mining17.03.049.

11. Taran, I., & Klymenko, I. (2017). Analysis of hydrostatic mechanical transmission efficiency in the process of wheeled vehicle braking. Transport Problems, 12(Special Edition), 45-56. https://doi.org/10.20858/tp.12.se.4.

12. Kurhan, D. M. (2023). Entropy Application for Simulation the Ballast State as a Railway Element. Acta Polytechnica Hungarica, 20(1), 63-77. https://doi.org/10.12700/APH.20.1.2023.20.5.

13. Kurhan, M. B., Kurhan, D. M., Husak, M. A., & Hmelevska, N. (2022). Development of the High-Speed Running of Trains in Ukraine for Integration with the International Railway Network. Acta Polytechnica Hungarica, 19(3), 207-218. https://doi.org/10.12700/APH.19.3.2022.3.16.

14. Károlyfi, K. (2017). The effect of saturation degree of cement paste on fair-faced concrete surfaces. Építöanyag (Online), (2), 55. https://doi.org/10.14382/epitoanyag-jsbcm.2017.10.

15. Kuchak, A. J. T., Marinkovic, D., & Zehn, M. (2020). Finite element model updating – Case study of a rail damper. Structural Engineering and Mechanics, 73(1), 27-35. https://doi.org/10.12989/sem.2020.73.1.027.

16. Kuchak, A. J. T., Marinkovic, D., & Zehn, M. (2021). Parametric Investigation of a Rail Damper Design Based on a Lab-Scaled Model. Journal of Vibration Engineering and Technologies, 9(1), 51-60. https://doi.org/10.1007/s42417-021-00341-7.

17. Taran, I., & Bondarenko, A. (2017). Conceptual approach to select parameters of hydrostatic and mechanical transmissions for wheel tractors designed for agricultural operations. Archives of transport,  41(1), 89-100. https://doi.org/10.5604/01.3001.0009.7389.

18. Saukenova, I., Oliskevych, M., Taran, I., Toktamyssova, A., Aliakbarkyzy, D., & Pelo, R. (2022). Optimization of schedules for early garbage collection and disposal in the megapolis. Eastern-European Journal of Enterprise Technologies, 1(3-115), 13-23. https://doi.org/10.15587/1729-4061.2022.251082.

19. Taran, I., & Litvin, V. (2018). Determination of rational parameters for urban bus route with combined operating mode. Transport Problems, 13(4), 157-171. https://doi.org/10.20858/tp.2018.13.4.14.

20. González, J. I., & Salazar, F. (2018). Advances in the modelling of railway ballast using the Discrete Element Method (DEM). The Fourth International Conference on Railway Technology, presentation. Retrieved from https://www.researchgate.net/publication/328042347.

21. Guo, Y., Markine, V., Song, J., & Jing, G. (2018). Ballast degradation: Effect of particle size and shape using Los Angeles Abrasion test and image analysis. Elsevier, Construction and Building Materials, 169, 414-424. https://doi.org/10.1016/j.conbuildmat.2018.02.170.

22. Wnek, M. A., Tutumluer, E., Moaveni, M., & Gehringer, E. (2013). Investigation of Aggregate Properties Influencing Railroad Ballast Performance. Journal of the Transportation Research Board, (2374), 180-189. https://doi.org/10.3141/2374-21.

23. Mohajerani, A., Nguyen, B. T., Tanriverdi, Y., & Chandrawanka, K. (2017). A new practical method for determining the LA abrasion value for aggregates. Elsevier B. V., Soils and Foundations, 57, 840-848. https://doi.org/10.1016/j.sandf.2017.08.013.

24. Fischer, S. (2023). Evaluation of inner shear resistance of layers from mineral granular materials. Facta Universitatis, Series: Mechanical Engineering. https://doi.org/10.22190/FUME230914041F.

25. Szalai, S., Eller, B., Juhász, E., Movahedi Rad, M., Németh, A., Harrach, D., Baranyai, G., & Fischer, Sz. (2022). Investigation of deformations of ballasted railway track during collapse using the Digital Image Correlation Method (DICM). Reports in Mechanical Engineering, 3(1), 258-282. https://doi.org/10.31181/rme20016032022s.

26. Juhász, E., Movahedi Rad, M., Fekete, I., & Fischer, S. (2019). Discrete element modelling of particle degradation of railway ballast material with PFC3D software. Nauka ta Progres Transportu, 6(84), 103-116. https://doi.org/10.15802/stp2019/194472.

27. Jia, W., Markine, V., & Guo, Y. (2023). Efficiency analysis and optimisation of DEM for railway ballast track simulations: Multi-layer shape model of lateral resistance. Transportation Geotechnics, 40, 100977. https://doi.org/10.1016/j.trgeo.2023.100977.

28. Lu, M., & McDowell, G. R. (2007). The importance of modelling ballast particle shape in the discrete element method. Granular Matter, 9(1-2), 69-80. https://doi.org/10.1007/s10035-006-0021-3.

29. European Committee for Standardization (2012). Unbound and hydraulically bound mixtures. Part 2: Test methods for laboratory reference density and water content. Proctor compaction (EN 13286-2:2010/AC:2012). Retrieved from https://standards.iteh.ai/catalog/standards/cen/5b4df027-90e4-4ccd-a119-e6ac12b80cd1/en-13286-2-2010-ac-2012.

30. Indraratna, B., Salim, W., & Rujikiatkamjorn, C. (2011). Advanced rail geotechnology – Ballasted track. CRC Press Taylor & Francis Group, London. ISBN 978-0-415-66957-3.

31. Lichtberger, B. (2005). Track compendium. Hamburg: Eurailpress Tetzlaff-Hestra GmbH & Co. KG.

32. Gálos, M., Kárpáti, L., & Szekeres, D. (2011). Ágyazati kőanyagok. A kutatás eredményei (2. rész). Sínek Világa, 53(1), 6-13. Retrieved from https://www.sinekvilaga.hu/documents/2011_1.pdf.

• < Prev
• Next >